Alle Werkstoffdatenblätter sind frei verfügbar. Kostenlose Registrierung unter www.materialdatacenter.com
Material Data Center ist ein weltweit führendes Informationssystem für Kunststoffe und bietet eine umfangreiche Kunststoffdatenbank, Berechnungsprogramme, CAE Schnittstellen, eine Literaturdatenbank und eine Bauteildatenbank. Für mehr Informationen über Material Data Center besuchen Sie www.materialdatacenter.com.
Dies ist das kostenlose Material Data Center Datenblatt für Ultraform® H2320 006 AT - POM - BASF
Material Data Center bietet Ihnen folgende Funktionalität für Ultraform® H2320 006 AT an:
Einheitenkonvertierung, PDF Datenblattdruck, direkter Vergleich mit anderen Kunststoffen, Schnapphakenberechnung, Biegebalkenberechnung, CAE Schnittstellen
Einheitenkonvertierung, PDF Datenblattdruck, direkter Vergleich mit anderen Kunststoffen, Schnapphakenberechnung, Biegebalkenberechnung, CAE Schnittstellen
Hier finden Sie eine Übersicht über weitere Informationen, die Material Data Center zu Ultraform bietet.
Die folgenden Links führen Sie direkt zu den entsprechenden Daten in diesem Datenblatt:
Produkttext
Hochmolekulare Marke mit etwas angehobener Fließfähigkeit zum Spritzgießen von dickwandigen Formteilen.
Abgekürzte Bezeichnung gemäß ISO 1043-1: POM
Bezeichnung gemäß ISO 29988-POM-K,,M-GNR,1-2
Abgekürzte Bezeichnung gemäß ISO 1043-1: POM
Bezeichnung gemäß ISO 29988-POM-K,,M-GNR,1-2
| Verarbeitungs-/Physikal. Eigenschaften | Wert | Einheit | Prüfnorm | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO Daten | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Schmelzevolumenrate, MVR | 2.9 | cm³/10min | ISO 1133 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Temperatur | 190 | °C | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Belastung | 2.16 | kg | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Verarbeitungsschwindung, parallel | 2.1 | % | ISO 294-4, 2577 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Verarbeitungsschwindung, senkrecht | 2.1 | % | ISO 294-4, 2577 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Mechanische Eigenschaften | Wert | Einheit | Prüfnorm | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO Daten | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Zug-Modul | 2600 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Streckspannung | 62 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Streckdehnung | 11 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Nominelle Bruchdehnung | 30 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Zug-Kriechmodul, 1h | 1800 | MPa | ISO 899-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Zug-Kriechmodul, 1000h | 1300 | MPa | ISO 899-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Charpy-Schlagzähigkeit, +23°C | 270 | kJ/m² | ISO 179/1eU | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Charpy-Schlagzähigkeit, -30°C | 260 | kJ/m² | ISO 179/1eU | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Charpy-Kerbschlagzähigkeit, +23°C | 6.5 | kJ/m² | ISO 179/1eA | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Charpy-Kerbschlagzähigkeit, -30°C | 5.5 | kJ/m² | ISO 179/1eA | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Thermische Eigenschaften | Wert | Einheit | Prüfnorm | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO Daten | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Schmelztemperatur, 10°C/min | 165 | °C | ISO 11357-1/-3 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Formbeständigkeitstemperatur, 1.80 MPa | 95 | °C | ISO 75-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Formbeständigkeitstemperatur, 0.45 MPa | 156 | °C | ISO 75-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Vicat-Erweichungstemperatur, B | 150 | °C | ISO 306 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Längenausdehnungskoeffizient, parallel | 120 | E-6/K | ISO 11359-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Brennbarkeit bei nominal 1.5mm | HB | class | IEC 60695-11-10 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| geprüfte Probekörperdicke | 1.6 | mm | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Yellow Card vorhanden | ja | - | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Brennbarkeit bei Dicke h | HB | class | IEC 60695-11-10 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| geprüfte Probekörperdicke | 0.8 | mm | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Yellow Card vorhanden | ja | - | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Brennbarkeit-Sauerstoff-Index | 15 | % | ISO 4589-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Elektrische Eigenschaften | Wert | Einheit | Prüfnorm | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ISO Daten | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Dielektrizitätszahl, 100Hz | 3.8 | - | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Dielektrizitätszahl, 1MHz | 3.8 | - | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Dielektr. Verlustfaktor, 100Hz | 10 | E-4 | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Dielektr. Verlustfaktor, 1MHz | 50 | E-4 | IEC 62631-2-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Spezifischer Durchgangswiderstand | 1E11 | Ohm*m | IEC 62631-3-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Spezifischer Oberflächenwiderstand | 1E13 | Ohm | IEC 62631-3-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Elektrische Durchschlagfestigkeit | 40 | kV/mm | IEC 60243-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Vergleichszahl der Kriechwegbildung | 600 | - | IEC 60112 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Andere Eigenschaften | Wert | Einheit | Prüfnorm |
| Wasseraufnahme | 0.9 | % | Ähnlich ISO 62 |
| Feuchtigkeitsaufnahme | 0.2 | % | Ähnlich ISO 62 |
| Dichte | 1410 | kg/m³ | ISO 1183 |
| Verarbeitungsempfehlungen Spritzguss | Wert | Einheit | Prüfnorm |
| Vortrocknung - Temperatur | 100 | °C | - |
| Vortrocknung - Zeit | 3 | h | - |
| Verarbeitungsfeuchte | ≤0.2 | % | - |
| Massetemperatur | 190 - 230 | °C | - |
| Werkzeugtemperatur | 60 - 120 | °C | - |
Merkmale
Verarbeitungsmethoden
Spritzgießen, Folienextrusion, Profilextrusion, Plattenextrusion, übrige Extrusion
Lieferformen
Granulat
Additive
Entformungshilfsmittel
Merkmale
Copolymer
Regionale Verfügbarkeit
Weitere Informationen
Spritzgießen
PREPROCESSING
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
injection molding, Melt temperature, range: 190 - 230 °C
injection molding, Melt temperature, recommended: 200 °C
injection molding, Mold temperature, range: 60 - 120 °C
injection molding, Mold temperature, recommended: 90 °C
injection molding, Dwell time, thermoplastics: 10 min
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
injection molding, Melt temperature, range: 190 - 230 °C
injection molding, Melt temperature, recommended: 200 °C
injection molding, Mold temperature, range: 60 - 120 °C
injection molding, Mold temperature, recommended: 90 °C
injection molding, Dwell time, thermoplastics: 10 min
Folienextrusion
PREPROCESSING
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
Extrusion, Blown film, Melt temperature: 175 - 180 °C
Extrusion, Flat film, Melt temperature: 175 - 180 °C
Processing
Ultraform can be processed to particular advantage using three-section screws having a total length L of 20 - 25 D and a constant pitch of about 1 D. However short-compression zone screws may also be used.
Pretreatment
Granules or pellets in original packaging can be processed without any special pretreatment. Granules or pellets which have become moist due to prolonged or incorrect storage (e.g. by formation of condensed water) must be dried in dehumidifying or recirculating air dryers for approx. 3 hours at about 100 - 110 °C. The moisture content should not exceed 0.2 %.
Postprocessing
Due to the different solidification and cooling of the melt which varies according to time and place stresses may arise, especially in the case of large wall thicknesses. These stresses can be removed by subsequent heat treatment. Tempering is essential when high demands are placed on dimensional stability. It can be carried out in air, liquid wax or oil at temperatures of 130 - 150, usually 140 - 145 °C. Lower temperatures are not effective. Duration: 10 minutes per 1 mm wall thickness.
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
Extrusion, Blown film, Melt temperature: 175 - 180 °C
Extrusion, Flat film, Melt temperature: 175 - 180 °C
Processing
Ultraform can be processed to particular advantage using three-section screws having a total length L of 20 - 25 D and a constant pitch of about 1 D. However short-compression zone screws may also be used.
Pretreatment
Granules or pellets in original packaging can be processed without any special pretreatment. Granules or pellets which have become moist due to prolonged or incorrect storage (e.g. by formation of condensed water) must be dried in dehumidifying or recirculating air dryers for approx. 3 hours at about 100 - 110 °C. The moisture content should not exceed 0.2 %.
Postprocessing
Due to the different solidification and cooling of the melt which varies according to time and place stresses may arise, especially in the case of large wall thicknesses. These stresses can be removed by subsequent heat treatment. Tempering is essential when high demands are placed on dimensional stability. It can be carried out in air, liquid wax or oil at temperatures of 130 - 150, usually 140 - 145 °C. Lower temperatures are not effective. Duration: 10 minutes per 1 mm wall thickness.
Übrige Extrusion
PREPROCESSING
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
Extrusion, Prepreg, Melt temperature: 175 - 180 °C
Extrusion, Pipes, Melt temperature: 175 - 180 °C
Extrusion, cable sheathing, Melt temperature: 175 - 180 °C
Processing
Ultraform can be processed to particular advantage using three-section screws having a total length L of 20 - 25 D and a constant pitch of about 1 D. However short-compression zone screws may also be used.
Pretreatment
Granules or pellets in original packaging can be processed without any special pretreatment. Granules or pellets which have become moist due to prolonged or incorrect storage (e.g. by formation of condensed water) must be dried in dehumidifying or recirculating air dryers for approx. 3 hours at about 100 - 110 °C. The moisture content should not exceed 0.2 %.
Postprocessing
Due to the different solidification and cooling of the melt which varies according to time and place stresses may arise, especially in the case of large wall thicknesses. These stresses can be removed by subsequent heat treatment. Tempering is essential when high demands are placed on dimensional stability. It can be carried out in air, liquid wax or oil at temperatures of 130 - 150, usually 140 - 145 °C. Lower temperatures are not effective. Duration: 10 minutes per 1 mm wall thickness.
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
Extrusion, Prepreg, Melt temperature: 175 - 180 °C
Extrusion, Pipes, Melt temperature: 175 - 180 °C
Extrusion, cable sheathing, Melt temperature: 175 - 180 °C
Processing
Ultraform can be processed to particular advantage using three-section screws having a total length L of 20 - 25 D and a constant pitch of about 1 D. However short-compression zone screws may also be used.
Pretreatment
Granules or pellets in original packaging can be processed without any special pretreatment. Granules or pellets which have become moist due to prolonged or incorrect storage (e.g. by formation of condensed water) must be dried in dehumidifying or recirculating air dryers for approx. 3 hours at about 100 - 110 °C. The moisture content should not exceed 0.2 %.
Postprocessing
Due to the different solidification and cooling of the melt which varies according to time and place stresses may arise, especially in the case of large wall thicknesses. These stresses can be removed by subsequent heat treatment. Tempering is essential when high demands are placed on dimensional stability. It can be carried out in air, liquid wax or oil at temperatures of 130 - 150, usually 140 - 145 °C. Lower temperatures are not effective. Duration: 10 minutes per 1 mm wall thickness.
Profilextrusion
PREPROCESSING
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
Extrusion, Profiles, Melt temperature: 175 - 180 °C
Processing
Ultraform can be processed to particular advantage using three-section screws having a total length L of 20 - 25 D and a constant pitch of about 1 D. However short-compression zone screws may also be used.
Pretreatment
Granules or pellets in original packaging can be processed without any special pretreatment. Granules or pellets which have become moist due to prolonged or incorrect storage (e.g. by formation of condensed water) must be dried in dehumidifying or recirculating air dryers for approx. 3 hours at about 100 - 110 °C. The moisture content should not exceed 0.2 %.
Postprocessing
Due to the different solidification and cooling of the melt which varies according to time and place stresses may arise, especially in the case of large wall thicknesses. These stresses can be removed by subsequent heat treatment. Tempering is essential when high demands are placed on dimensional stability. It can be carried out in air, liquid wax or oil at temperatures of 130 - 150, usually 140 - 145 °C. Lower temperatures are not effective. Duration: 10 minutes per 1 mm wall thickness.
Pre/Post-processing, max. allowed water content: .2 %
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 3 h
PROCESSING
Extrusion, Profiles, Melt temperature: 175 - 180 °C
Processing
Ultraform can be processed to particular advantage using three-section screws having a total length L of 20 - 25 D and a constant pitch of about 1 D. However short-compression zone screws may also be used.
Pretreatment
Granules or pellets in original packaging can be processed without any special pretreatment. Granules or pellets which have become moist due to prolonged or incorrect storage (e.g. by formation of condensed water) must be dried in dehumidifying or recirculating air dryers for approx. 3 hours at about 100 - 110 °C. The moisture content should not exceed 0.2 %.
Postprocessing
Due to the different solidification and cooling of the melt which varies according to time and place stresses may arise, especially in the case of large wall thicknesses. These stresses can be removed by subsequent heat treatment. Tempering is essential when high demands are placed on dimensional stability. It can be carried out in air, liquid wax or oil at temperatures of 130 - 150, usually 140 - 145 °C. Lower temperatures are not effective. Duration: 10 minutes per 1 mm wall thickness.
Plattenextrusion
VORBEHANDLUNG
Pre/Post-processing max. zul. Wassergehalt evtl. Trocknung: .2 %
Pre/Post-processing Vortrocknung Temperatur: 100 °C
Pre/Post-processing Vortrocknung Zeit: 3 h
VERARBEITUNG
Extrusion Platten Massetemperatur: 175 - 180 °C
Verarbeitung
Ultraform® kann besonders vorteilhaft mit Dreizonen-Schnecken mit einer Gesamtlänge L von 20 - 25 D und einer konstanten Gangsteigung von ca. 1 D verarbeitet werden. Jedoch können auch Kurzkompressionsschnecken verwendet werden.
Vorbehandlung
Das originalverpackte Granulat kann ohne besondere Vorbehandlung verarbeitet werden. Durch längere oder unsachgemäße Lagerung (z.B. durch Kondenswasserbildung) feucht gewordenes Granulat muss in Trockenluft- oder Umlufttrocknern bei ca. 100 - 110 °C etwa 3 Stunden lang getrocknet werden. Der Wassergehalt sollte 0.2 % nicht überschreiten.
Nachbehandlung
Bedingt durch das zeitlich und örtlich unterschiedliche Erstarren und die Abkühlung der Schmelze können Spannungen entstehen, insbesondere bei hohen Wanddicken. Diese Spannungen lassen sich durch eine nachträgliche Wärmebehandlung abbauen. Bei hohen Anforderungen an die Dimensionsstabilität ist die Temperung unumgänglich. Sie kann in Luft, Flüssigwachs oder Öl bei Temperaturen von 130 - 150, meist 140 - 145 °C durchgeführt werden. Niedrigere Temperaturen sind wenig effizient. Dauer: 10 Minuten pro 1 mm Wanddicke.
Pre/Post-processing max. zul. Wassergehalt evtl. Trocknung: .2 %
Pre/Post-processing Vortrocknung Temperatur: 100 °C
Pre/Post-processing Vortrocknung Zeit: 3 h
VERARBEITUNG
Extrusion Platten Massetemperatur: 175 - 180 °C
Verarbeitung
Ultraform® kann besonders vorteilhaft mit Dreizonen-Schnecken mit einer Gesamtlänge L von 20 - 25 D und einer konstanten Gangsteigung von ca. 1 D verarbeitet werden. Jedoch können auch Kurzkompressionsschnecken verwendet werden.
Vorbehandlung
Das originalverpackte Granulat kann ohne besondere Vorbehandlung verarbeitet werden. Durch längere oder unsachgemäße Lagerung (z.B. durch Kondenswasserbildung) feucht gewordenes Granulat muss in Trockenluft- oder Umlufttrocknern bei ca. 100 - 110 °C etwa 3 Stunden lang getrocknet werden. Der Wassergehalt sollte 0.2 % nicht überschreiten.
Nachbehandlung
Bedingt durch das zeitlich und örtlich unterschiedliche Erstarren und die Abkühlung der Schmelze können Spannungen entstehen, insbesondere bei hohen Wanddicken. Diese Spannungen lassen sich durch eine nachträgliche Wärmebehandlung abbauen. Bei hohen Anforderungen an die Dimensionsstabilität ist die Temperung unumgänglich. Sie kann in Luft, Flüssigwachs oder Öl bei Temperaturen von 130 - 150, meist 140 - 145 °C durchgeführt werden. Niedrigere Temperaturen sind wenig effizient. Dauer: 10 Minuten pro 1 mm Wanddicke.
Haftungsausschluss
Copyright Altair Engineering GmbH. Die Altair Engineering GmbH übernimmt keine Haftung für die Fehlerfreiheit dieser Informationen. Der Einsatz der Daten erfolgt in der alleinigen Verantwortung des Nutzers unter Ausschluss jeglicher Haftung der Altair Engineering GmbH; dies gilt insbesondere für Ansprüche auf Ersatz von Folgeschäden. Es wird ausdrücklich darauf hingewiesen, dass jegliche Entscheidung über die Anwendung von Werkstoffen mit dem Produzenten des jeweiligen Materials abgesprochen werden muss. Dies bezieht sich auf alle Inhalte dieses Systems. Weiterhin sind die Hinweise zum Urheberrecht zu beachten.
Erstellt: Quelle: www.materialdatacenter.com
Material Data Center wird von M-Base Engineering + Software GmbH angeboten. M-Base Engineering + Software GmbH übernimmt keinerlei Gewährleistung, dass das System fehlerfrei ist. Jegliche Entscheidung über die Anwendung von Werkstoffen muss mit dem jeweiligen Produzenten einzeln abgeklärt werden.
Weiterführende Informationen zu diesem Material wie Stoffgruppe, Herstelleradresse, evtl. auch Datenblätter und Anwendungsbeispiele finden Sie auf www.materialdatacenter.com. Ein Teil der Informationen sind registrierten Nutzern vorbehalten. Auf der Startseite finden Sie einen Link zur kostenlosen Registrierung.