Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of Promyde® B30 P2 G20 MI - PA6-GF20 - Nurel S.A.
Material Data Center offers the following functions for Promyde® B30 P2 G20 MI:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our
disclaimer.
| Processing/Physical Characteristics | dry / cond | Unit | Test Standard |
| ISO Data |
| Melt volume-flow rate, MVR |
30 / * |
cm³/10min |
ISO 1133 |
| Temperature |
275 / * |
°C |
- |
| Load |
5 / * |
kg |
- |
| Molding shrinkage, parallel |
0.3 / * |
% |
ISO 294-4, 2577 |
| Molding shrinkage, normal |
0.4 / * |
% |
ISO 294-4, 2577 |
| Mechanical properties | dry / cond | Unit | Test Standard |
| ISO Data |
| Tensile Modulus |
5000 / 2900 |
MPa |
ISO 527 |
| Tensile Strength |
110 / 70 |
MPa |
ISO 527 |
| Strain at break |
4.5 / - |
% |
ISO 527 |
| Flexural modulus, 23°C |
4500 / 2800 |
MPa |
ISO 178 |
| Flexural strength |
145 / 85 |
MPa |
ISO 178 |
| Charpy notched impact strength, +23°C |
16 / 30 |
kJ/m² |
ISO 179/1eA |
| Charpy notched impact strength, -30°C |
10 / - |
kJ/m² |
ISO 179/1eA |
| Thermal properties | dry / cond | Unit | Test Standard |
| ISO Data |
| Melting temperature, 10°C/min |
222 / * |
°C |
ISO 11357-1/-3 |
| Temp. of deflection under load, 1.80 MPa |
195 / * |
°C |
ISO 75-1/-2 |
| Temp. of deflection under load, 0.45 MPa |
200 / * |
°C |
ISO 75-1/-2 |
| Coeff. of linear therm. expansion, parallel |
30 / * |
E-6/K |
ISO 11359-1/-2 |
| Coeff. of linear therm. expansion, normal |
70 / * |
E-6/K |
ISO 11359-1/-2 |
| Electrical properties | dry / cond | Unit | Test Standard |
| ISO Data |
| Comparative tracking index |
500 / - |
- |
IEC 60112 |
| Other Standards[S] |
| Relative permittivity, 1MHz |
3.7 / 6.8 |
- |
IEC 60250 |
| Dissipation factor, 1MHz |
250 / 2200 |
E-4 |
IEC 60250 |
| Volume resistivity |
1E13 / 1E10 |
Ohm*m |
IEC 60093 |
| Surface resistivity |
* / 1E10 |
Ohm |
IEC 60093 |
| S: | These properties are reported by the producer according standards that are different to our defaults. |
| Other properties | dry / cond | Unit | Test Standard |
| Water absorption |
6.8 / * |
% |
Sim. to ISO 62 |
| Humidity absorption |
2 / * |
% |
Sim. to ISO 62 |
| Density |
1260 / - |
kg/m³ |
ISO 1183 |
| Material specific properties | dry / cond | Unit | Test Standard |
| ISO Data |
| Viscosity number |
145 / * |
cm³/g |
ISO 307, 1157, 1628 |
| Processing Recommendation Injection Molding | Value | Unit | Test Standard |
| Pre-drying - Temperature |
<80 |
°C |
- |
| Pre-drying - Time |
4 - 6 |
h |
- |
| Melt temperature |
260 - 290 |
°C |
- |
| Mold temperature |
40 - 80 |
°C |
- |
Characteristics
Processing
Injection Molding
Special Characteristics
High impact or impact modified, Heat stabilized or stable to heat
Regional Availability
Europe
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.
