Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Stylac IC10N - ABS - Asahi Kasei

Material Data Center offers the following functions for Stylac IC10N:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Stylac datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 1 cm³/10min ISO 1133
Temperature 220 °C -
Load 10 kg -
Melt flow index, MFI 2 g/10min ISO 1133
Temperature 220 °C -
Load 10 kg -
ASTM Data
Mold Shrinkage, MD 0.0015 mm/mm ASTM D 955
Mechanical propertiesValueUnitTest Standard
ISO Data
Flexural modulus, 23°C 10000 MPa ISO 178
Flexural strength 186 MPa ISO 178
Charpy notched impact strength, +23°C 8 kJ/m² ISO 179/1eA
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 100 °C ISO 75-1/-2
Vicat softening temperature, B 110 °C ISO 306
ASTM Data
UL 94 Flame rating HB - UL 94
Thickness tested 1.5 mm -
Thermal Conductivity, solid state 0.0375 W/(m K) ASTM C 177
Electrical propertiesValueUnitTest Standard
ASTM Data
Surface Resistivity 4 Ohm ASTM D 257
Other propertiesValueUnitTest Standard
Density 1120 kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 75 - 90 °C -
Pre-drying - Time 3 - 4 h -
Mold temperature 40 - 70 °C -
Zone 1 200 - 230 °C -
Zone 2 200 - 240 °C -
Zone 3 220 - 260 °C -
Nozzle temperature 210 - 245 °C -
Maximum residence time 20 min -
Characteristics
Processing
Injection Molding
Special Characteristics
Increased electrical conductivity
Regional Availability
North America, Europe, Asia Pacific
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.