Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of XAREC® WA 550 - (PS-SY)-GF30 - Idemitsu Chemicals
Material Data Center offers the following functions for XAREC® WA 550:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Xarec datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our
disclaimer.
| Processing/Physical Characteristics | Value | Unit | Test Standard |
| Other Standards[S] |
| Molding shrinkage, parallel |
0.2 |
% |
Producer Method |
| Molding shrinkage, normal |
0.5 |
% |
Producer Method |
| S: | These properties are reported by the producer according standards that are different to our defaults. |
| Mechanical properties | Value | Unit | Test Standard |
| ISO Data |
| Tensile Modulus |
10000 |
MPa |
ISO 527 |
| Stress at break |
135 |
MPa |
ISO 527 |
| Strain at break |
1.8 |
% |
ISO 527 |
| Flexural modulus, 23°C |
9800 |
MPa |
ISO 178 |
| Flexural strength |
200 |
MPa |
ISO 178 |
| Charpy impact strength, +23°C |
47 |
kJ/m² |
ISO 179/1eU |
| Charpy notched impact strength, +23°C |
13 |
kJ/m² |
ISO 179/1eA |
| Izod impact strength, +23°C |
39 |
kJ/m² |
ISO 180/1U |
| Izod notched impact strength, +23°C |
12 |
kJ/m² |
ISO 180/1A |
| Thermal properties | Value | Unit | Test Standard |
| ISO Data |
| Temp. of deflection under load, 1.80 MPa |
250 |
°C |
ISO 75-1/-2 |
| Temp. of deflection under load, 0.45 MPa |
270 |
°C |
ISO 75-1/-2 |
| Coeff. of linear therm. expansion, parallel |
20 |
E-6/K |
ISO 11359-1/-2 |
| Coeff. of linear therm. expansion, normal |
44 |
E-6/K |
ISO 11359-1/-2 |
| Burning behav. at 1.5 mm nom. thickn. |
HB |
class |
IEC 60695-11-10 |
| Thickness tested |
1.5 |
mm |
- |
| Yellow Card available |
yes |
- |
- |
| Electrical properties | Value | Unit | Test Standard |
| ISO Data |
| Comparative tracking index |
500 |
- |
IEC 60112 |
| ASTM Data |
| Dielectric Strength, Short Time |
25 |
kV/mm |
ASTM D 149 |
| Arc Resistance |
150 |
s |
ASTM D 495 |
| Other Standards[S] |
| Relative permittivity, 1MHz |
3.1 |
- |
IEC 60250 |
| Dissipation factor, 1MHz |
10 |
E-4 |
IEC 60250 |
| Volume resistivity |
1E14 |
Ohm*m |
IEC 60093 |
| S: | These properties are reported by the producer according standards that are different to our defaults. |
| Other properties | Value | Unit | Test Standard |
| Density |
1270 |
kg/m³ |
ISO 1183 |
| Processing Recommendation Injection Molding | Value | Unit | Test Standard |
| Pre-drying - Temperature |
120 |
°C |
- |
| Pre-drying - Time |
3 - 5 |
h |
- |
| Melt temperature |
280 - 310 |
°C |
- |
| Mold temperature |
130 - 155 |
°C |
- |
Characteristics
Processing
Injection Molding
Delivery form
Pellets
Applications
Automotive
Regional Availability
North America, Europe, Asia Pacific
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.
