Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox. Information about Biopolymers, a project by FH Hannover and M-Base Engineering & Software GmbH sponsored by Fachagentur Nachwachsende Rohstoffe (FNR).

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of INNOPOL® CS 2-2910 WF - PP-W10 - Inno-Comp Kft.

Material Data Center offers the following functions for INNOPOL® CS 2-2910 WF:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Innopol datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt flow index, MFI 17 g/10min ISO 1133
Temperature 230 °C -
Load 2.16 kg -
Molding shrinkage, parallel 1.3 % ISO 294-4, 2577
Molding shrinkage, normal 1.2 % ISO 294-4, 2577
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 1750 MPa ISO 527
Yield stress 27 MPa ISO 527
Yield strain 3.3 % ISO 527
Nominal strain at break 4.7 % ISO 527
Flexural strength 39 MPa ISO 178
Charpy impact strength, +23°C 18.5 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 3.6 kJ/m² ISO 179/1eA
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 59 °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 125 °C ISO 75-1/-2
Other propertiesValueUnitTest Standard
Density 930 kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 105 °C -
Pre-drying - Time 2 h -
Processing humidity ≤0.07 % -
Melt temperature 170 - 180 °C -
Mold temperature 60 - 80 °C -
Zone 1 160 - 200 °C -
Characteristics
Processing
Injection Molding
Delivery form
Natural Color
Features
Copolymer
Certifications
Contains renewable resources
Regional Availability
Europe
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.