Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of MAGNUM™ 357 HP - ABS - Trinseo

Material Data Center offers the following functions for MAGNUM™ 357 HP:
unit conversion, PDF datasheet print, comparison with other plastics, cooling time calculation, CAE Interfaces

Check here, which other Magnum datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Density of melt 1080 kg/m³ -
Thermal conductivity of melt 0.13 W/(m K) -
Spec. heat capacity of melt 1890 J/(kg K) -
Ejection temperature 127 °C -
ASTM Data
Melt Flow Index, MFI 2 g/10min ASTM D 1238
Temperature 230 °C -
Load 3.8 kg -
Mold Shrinkage, MD 0.0055 mm/mm ASTM D 955
Mechanical propertiesValueUnitTest Standard
ASTM Data
Tensile Modulus 1999 MPa ASTM D 638
Tensile Strength at Yield 37.9 MPa ASTM D 638
Tensile Strength at Break 33.1 MPa ASTM D 638
Elongation at Break 45 % ASTM D 638
Flexural Modulus 2206 MPa ASTM D 790
Flexural Strength 62.1 MPa ASTM D 790
Izod Impact notched, 1/8 in 310 J/m ASTM D 256
Izod Impact notched, Low-Temperature 128 J/m ASTM D 256
Temperature -17.8 °C -
Thermal propertiesValueUnitTest Standard
ASTM Data
Coefficient of Thermal Expansion, MD 81 E-6/K ASTM D 696
DTUL @ 66 psi 104 °C ASTM D 648
DTUL @ 264 psi 87.8 °C ASTM D 648
Vicat Temperature 120 °C ASTM D 1525
Other propertiesValueUnitTest Standard
Density 1060 kg/m³ ASTM D 792
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 82.2 - 85 °C -
Pre-drying - Time 2 - 4 h -
Processing humidity ≤0.1 % -
Melt temperature 260 - 282 °C -
Mold temperature 37.8 - 82.2 °C -
Back pressure 0.345 - 0.689 MPa -
Characteristics
Processing
Injection Molding, Profile Extrusion, Sheet Extrusion, Thermoforming
Special Characteristics
Heat stabilized or stable to heat
Applications
Automotive
Regional Availability
North America, South and Central America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.