Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of APLAX® P2413GN B33 - PP-T20 - Ginar Technology Co.,Ltd.

Material Data Center offers the following functions for APLAX® P2413GN B33:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Aplax datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Índice de fluidez, MFI 24 g/10min ISO 1133
Temperatura 230 °C -
Carga 2.16 kg -
Contracción posterior al moldeo, paralelo 1.2 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de fluencia 37 MPa ISO 527
Alargamiento a rotura 16.7 % ISO 527
Módulo de flexión, 23°C 4260 MPa ISO 178
Resistencia a la flexión 65.3 MPa ISO 178
Resistencia al impacto Izod con entalla, +23°C 2.83 kJ/m² ISO 180/1A
Dureza Rockwell R 105 - ISO 2039-2
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 166 °C ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa 98 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 143 °C ISO 75-1/-2
Ratio de combustión, FMVSS, espesor de 1mm 91.2 mm/min ISO 3795 (FMVSS 302)
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1070 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Negro
Características especiales
Estable contra el calor
Certifications
RoHS
Applicaciones
Automotriz
Disponibilidad regional
Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.