Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Badalac® ABS 30 - ABS - Bada AG

Material Data Center offers the following functions for Badalac® ABS 30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Badalac datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 34 cm³/10min ISO 1133
Temperatura 220 °C -
Carga 10 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 2300 MPa ISO 527
Esfuerzo de fluencia 44 MPa ISO 527
Alarg. en límite elástico 2.4 % ISO 527
Alarg. nominal a rotura 12 % ISO 527
Resistencia a la flexión 65 MPa ISO 178
Resistencia al impacto Charpy, +23°C 125 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C 9 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 19 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C 7 kJ/m² ISO 179/1eA
Resistencia al impacto Izod con entalla, +23°C 22 kJ/m² ISO 180/1A
Resistencia al impacto Izod con entalla 7 kJ/m² ISO 180/1A
Temperatura -30 °C -
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 94 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 99 °C ISO 75-1/-2
Temp. reblandecimiento Vicat, A 102 °C ISO 306
Temp. reblandecimiento Vicat, B 95 °C ISO 306
Coef.de expansión térmica lineal, paralelo 95 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 95 E-6/K ISO 11359-1/-2
Combustibilidad a espesor h HB class IEC 60695-11-10
Espesores de probeta 0.8 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 1MHz 2.8 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 79 E-4 IEC 62631-2-1
Resistividad volumétrica específica 1E11 Ohm*m IEC 62631-3-1
Resistividad superficial específica 1E13 Ohm IEC 62631-3-2
Resistencia dieléctrica 38 kV/mm IEC 60243-1
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.95 % Sim. to ISO 62
Absorción de humedad 0.24 % Sim. to ISO 62
Densidad 1040 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 °C -
Tiempo de pre-secado 2 - 4 h -
Humedad de procesamiento ≤0.1 % -
Temperatura de la masa 220 - 260 °C -
Temperatura del molde 30 - 80 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Alto impacto o modificado al impacto
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.