Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Durabio™ D6350 - PC - Mitsubishi Chemical Performance Polymers

Material Data Center offers the following functions for Durabio™ D6350:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Durabio datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 9 cm³/10min ISO 1133
Temperatura 230 °C -
Carga 2.16 kg -
Índice de fluidez, MFI 12 g/10min ISO 1133
Temperatura 230 °C -
Carga 2.16 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 2200 MPa ISO 527
Esfuerzo de tracción 70 MPa ISO 527
Alargamiento a rotura 110 % ISO 527
Módulo de flexión, 23°C 2500 MPa ISO 178
Resistencia a la flexión 95 MPa ISO 178
Resistencia al impacto Charpy, +23°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 8 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 90 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 101 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 71 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 71 E-6/K ISO 11359-1/-2
Propiedades opticasValorUnidadesMétodo de ensayo
ISO Data
Transmitancia luminosa 92 % ISO 13468-1, -2
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1340 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Tiempo de pre-secado 5 - 7 h -
Temperatura de la masa 230 - 250 °C -
Temperatura del molde 60 - 80 °C -
Temperatura - zona de alimentación 220 - 260 °C -
Zona 1 220 - 260 °C -
Temperatura de boquilla 220 - 260 °C -
Velocidad de giro de husillo 50 rpm -
Presión de inyección 50 - 95 MPa -
Contrapresión 10 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Negro
Características especiales
Transparente
Características
Light Guiding
Certifications
Contiene recursos renovables
Applicaciones
Automotriz, Electrica, Empacado, Equipos deportivos
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.