Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Hybrid S466 - (PC+ABS) - Ravago Manufacturing Americas

Material Data Center offers the following functions for Hybrid S466:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Hybrid S datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 2.1 cm³/10min ISO 1133
Temperatura 230 °C -
Carga 3.8 kg -
Contracción posterior al moldeo, paralelo 0.6 % ISO 294-4, 2577
ASTM Data
Índice de fluidez, MFI 2.4 g/10min ASTM D 1238
Temperatura 230 °C -
Carga 3.8 kg -
Contracción posterior al moldeo, paralelo 0.006 mm/mm ASTM D 955
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de fluencia 56 MPa ISO 527
Alargamiento a rotura >50 % ISO 527
Módulo de flexión, 23°C 2350 MPa ISO 178
Resistencia al impacto Izod con entalla, +23°C 48 kJ/m² ISO 180/1A
Resistencia al impacto Izod con entalla 37 kJ/m² ISO 180/1A
Temperatura -20 °C -
ASTM Data
Esfuerzo de fluencia a tracción 57.2 MPa ASTM D 638
Esfuerzo de fractura a tracción 55.2 MPa ASTM D 638
Alargamiento a la rotura 70 % ASTM D 638
Módulo de flexión 2340 MPa ASTM D 790
Resistencia al impacto Izod con entalla, 1/8 in 690 J/m ASTM D 256
Resistencia al impacto Izod con entalla, baja temperatura 500 J/m ASTM D 256
Temperatura -20 °C -
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 115 °C ISO 75-1/-2
ASTM Data
Combustibilidad UL 94 HB - UL 94
Espesores de probeta 1.5 mm -
Estabilidad al calor @ 264 psi 113 °C ASTM D 648
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1140 kg/m³ ISO 1183
Absorción de agua, 24hr 0.1 % ASTM D 570
Densidad 1140 kg/m³ ASTM D 792
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola, Negro, Color natural
Características especiales
Alto impacto o modificado al impacto
Applicaciones
Automotriz
Disponibilidad regional
Norteamérica
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.