Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LATILUB 80-15T G/30 - (PPS+PTFE)-GF - LATI Industria Termoplastici S.p.A.

Material Data Center offers the following functions for LATILUB 80-15T G/30:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Latilub datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 0.3 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.7 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 13500 MPa ISO 527
Resistencia a la tracción 120 MPa ISO 527
Alargamiento a rotura 1.4 % ISO 527
Resistencia al impacto Charpy, +23°C 35 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 8 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 265 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 275 °C ISO 75-1/-2
Temp. reblandecimiento Vicat, B 255 °C ISO 306
ASTM Data
Combustibilidad UL 94 V-0 - UL 94
Espesores de probeta 0.75 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ASTM Data
Resistividad superficial 1E12 Ohm ASTM D 257
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1620 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 100 - 130 °C -
Tiempo de pre-secado 3 h -
Temperatura de la masa 290 - 310 °C -
Temperatura del molde 130 - 150 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Aditivos
Lubricante
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.