View Datasheet in other language

E-mail to a friend

Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Maxxam™ TH-418.S001 6770 - PP - Avient Corporation

Material Data Center offers the following functions for Maxxam™ TH-418.S001 6770:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Maxxam datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:

Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección

Any use of this information falls under the rules of our disclaimer.

Caracteristicas de procesamiento y fisicas

Valor

Unidades

Método de ensayo

ASTM Data

Contracción posterior al moldeo, paralelo

0.017

mm/mm

ASTM D 955

Propiedades mecánicas

Valor

Unidades

Método de ensayo

ASTM Data

Esfuerzo de tracción

MPa

ASTM D 638

Módulo de flexión

1350

MPa

ASTM D 790

Resistencia al impacto Izod con entalla, 1/8 in

J/m

ASTM D 256

Propiedades térmicas

Valor

Unidades

Método de ensayo

ASTM Data

Estabilidad al calor @ 66 psi

°C

ASTM D 648

Propiedades eléctricas

Valor

Unidades

Método de ensayo

ASTM Data

Resistividad superficial

1E12

Ohm

ASTM D 257

Otras propiedades	Valor	Unidades	Método de ensayo
Densidad	902	kg/m³	ASTM D 792

Recomendación para procesamiento Moldeo por inyección	Valor	Unidades	Método de ensayo
Temperatura de pre-secado	80 - 85	°C	-
Tiempo de pre-secado	4 - 6	h	-
Temperatura de la masa	200 - 240	°C	-
Temperatura del molde	30 - 60	°C	-

Características

Procesamiento y forma de entrega

Moldeo por inyección

Características especiales

Estable contra rayos U.V./interperie, Estable contra el calor

Disponibilidad regional

Asia Pacifico

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.