Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NYLENE® 4214 - PA6 - Polymeric Resources Corporation

Material Data Center offers the following functions for NYLENE® 4214:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Nylene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ASTM Data
Módulo de tracción 1931 MPa ASTM D 638
Esfuerzo de tracción 46.7 MPa ASTM D 638
Alargamiento a la rotura 100 % ASTM D 638
Módulo de flexión 1731 MPa ASTM D 790
Resistencia al impacto Izod con entalla, 1/8 in 854 J/m ASTM D 256
Propiedades térmicasValorUnidadesMétodo de ensayo
ASTM Data
Estabilidad al calor @ 264 psi 43.3 °C ASTM D 648
Temperatura de fusión 216 °C ASTM D 3418
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1090 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 66 - 82 °C -
Tiempo de pre-secado 2 - 4 h -
Humedad de procesamiento ≤0.2 % -
Temperatura de la masa 249 - 282 °C -
Temperatura del molde 49 - 93 °C -
Zona 1 227 - 260 °C -
Zona 2 238 - 271 °C -
Zona 3 249 - 282 °C -
Temperatura de boquilla 249 - 282 °C -
Presión de inyección 7 - 15 MPa -
Contrapresión 0 - 50 MPa -
Presión de mantenimiento 5 - 12 MPa -
Tiempo de residencia máxima 6 min -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Alto impacto o modificado al impacto
Applicaciones
Automotriz
Disponibilidad regional
Norteamérica
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.