Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Pebax® Rnew® 80R53 SP 02 - TPA - ARKEMA

Check here, which other Pebax datasheets, application examples or technical articles are available in Material Data Center

Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Funciones

Any use of this information falls under the rules of our disclaimer.

Texto del producto

Polyether block Pebax® Rnew ® 80R53 SP 02 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide based on renewable resources. This SP grade has been developed to be heat and UV resistant.

According to ASTM D6866, the biobased carbon content is measured at 92%.

Main applications:

• Ski shoes
• Athletic foot wear components

Packaging:
This grade is delivered dried in sealed packaging (25 kg bags) ready to be processed.

Shelf Life:
Two years from the delivery. For any use above this limit, please refer to our technical services.

Propiedades mecánicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Módulo de tracción	- / 944	MPa	ISO 527
Esfuerzo de fluencia	- / 33	MPa	ISO 527
Alarg. en límite elástico	- / 24	%	ISO 527
Alarg. nominal a rotura	- / >50	%	ISO 527
Resistencia al impacto Charpy c/entalla, +23°C	- / 44	kJ/m²	ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C	- / 16	kJ/m²	ISO 179/1eA
Dureza Shore D	67 / *	-	ISO 7619-1

Propiedades térmicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Temperatura de fusión, 10°C/min	188 / *	°C	ISO 11357-1/-3

Otras propiedades	Seco / Cond	Unidades	Método de ensayo
Absorción de agua	0.7 / *	%	Sim. to ISO 62
Absorción de humedad	0.8 / *	%	Sim. to ISO 62
Densidad	1020 / 1020	kg/m³	ISO 1183
Biobased content	89	%	-

Funciones

Características

Procesamiento y forma de entrega

Moldeo por inyección, Otros tipos de extrusión

Forma de suministro

Sémola

Características especiales

Estable a la luz, Estable contra rayos U.V./interperie, Estable contra el calor

Certifications

Contiene recursos renovables

Disponibilidad regional

Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa

Demás información

Moldeo por inyección

Processing conditions:

- Typical melt temperature (Min / Recommended / Max) : 230°C / 260°C / 290°C.
- Typical mold temperature : 25 – 60°C.
- Drying time and temperature (only necessary for bags opened for more than two hours) : 5-7 hours at 70-80°C.

Otros tipos de extrusión

Processing conditions:

- Typical melt temperature (Min / Recommended / Max): 230°C / 260°C / 290°C.
- Drying time and temperature (only necessary for bags opened for more than two hours): 5-7 hours at 70-80°C.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.