Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of Promyde® B40 BR1 - PA6 - Nurel S.A.
Material Data Center offers the following functions for Promyde® B40 BR1:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center
Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our
disclaimer.
| Caracteristicas de procesamiento y fisicas | Seco / Cond | Unidades | Método de ensayo |
| ISO Data |
| Indice de fluidez volumétrico, MVR |
14 / * |
cm³/10min |
ISO 1133 |
| Temperatura |
275 / * |
°C |
- |
| Carga |
5 / * |
kg |
- |
| Contracción posterior al moldeo, paralelo |
1.0 / * |
% |
ISO 294-4, 2577 |
| Contracción posterior al moldeo, normal |
0.9 / * |
% |
ISO 294-4, 2577 |
| Propiedades mecánicas | Seco / Cond | Unidades | Método de ensayo |
| ISO Data |
| Módulo de tracción |
3400 / 1100 |
MPa |
ISO 527 |
| Esfuerzo de tracción |
90 / 40 |
MPa |
ISO 527 |
| Alarg. en límite elástico |
4 / 25 |
% |
ISO 527 |
| Alargamiento a rotura |
70 / 0 |
% |
ISO 527 |
| Módulo de flexión, 23°C |
2900 / 1000 |
MPa |
ISO 178 |
| Resistencia a la flexión |
115 / 30 |
MPa |
ISO 178 |
| Resistencia al impacto Charpy, +23°C |
N / N |
kJ/m² |
ISO 179/1eU |
| Resistencia al impacto Charpy c/entalla, +23°C |
6.2 / 38 |
kJ/m² |
ISO 179/1eA |
| Propiedades térmicas | Seco / Cond | Unidades | Método de ensayo |
| ISO Data |
| Temperatura de fusión, 10°C/min |
223 / * |
°C |
ISO 11357-1/-3 |
| Estabilidad al calor, 1.80 MPa |
65 / * |
°C |
ISO 75-1/-2 |
| Estabilidad al calor, 0.45 MPa |
197 / * |
°C |
ISO 75-1/-2 |
| Coef.de expansión térmica lineal, paralelo |
70 / * |
E-6/K |
ISO 11359-1/-2 |
| Coef.de expansión térmica lineal, normal |
100 / * |
E-6/K |
ISO 11359-1/-2 |
| Combustibilidad a 1.5mm esp. nom. |
V-2 / * |
class |
IEC 60695-11-10 |
| Espesores de probeta |
1.5 / * |
mm |
- |
| Propiedades eléctricas | Seco / Cond | Unidades | Método de ensayo |
| ISO Data |
| Indice comparativo de linea de fuga |
600 / - |
- |
IEC 60112 |
| Other Standards[S] |
| Constante dieléctrica, 1MHz |
3.5 / 7 |
- |
IEC 60250 |
| Factor de pérdidas dieléctricas, 1MHz |
300 / 3000 |
E-4 |
IEC 60250 |
| Resistividad volumétrica específica |
1E13 / 1E10 |
Ohm*m |
IEC 60093 |
| Resistividad superficial específica |
* / 1E10 |
Ohm |
IEC 60093 |
| S: | These properties are reported by the producer according standards that are different to our defaults. |
| Otras propiedades | Seco / Cond | Unidades | Método de ensayo |
| Absorción de agua |
9.5 / * |
% |
Sim. to ISO 62 |
| Absorción de humedad |
3 / * |
% |
Sim. to ISO 62 |
| Densidad |
1130 / - |
kg/m³ |
ISO 1183 |
| Propiedades específicas del material | Seco / Cond | Unidades | Método de ensayo |
| ISO Data |
| Indice de viscosidad |
263 / * |
cm³/g |
ISO 307, 1157, 1628 |
| Recomendación para procesamiento Moldeo por inyección | Valor | Unidades | Método de ensayo |
| Temperatura de pre-secado |
<80 |
°C |
- |
| Tiempo de pre-secado |
4 - 6 |
h |
- |
| Temperatura de la masa |
260 - 290 |
°C |
- |
| Temperatura del molde |
40 - 80 |
°C |
- |
Características
Procesamiento y forma de entrega
Moldeo por inyección
Aditivos
Lubricante
Características
Nucleado
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.
