Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® B300 P2 G60 S - PA6-GF60 - Nurel S.A.

Material Data Center offers the following functions for Promyde® B300 P2 G60 S:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 35 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carga 5 / * kg -
Contracción posterior al moldeo, paralelo 0.2 / * % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.3 / * % ISO 294-4, 2577
Propiedades mecánicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 21000 / 17000 MPa ISO 527
Esfuerzo de tracción 240 / 190 MPa ISO 527
Alargamiento a rotura 2.5 / 2.1 % ISO 527
Módulo de flexión, 23°C 19700 / 14400 MPa ISO 178
Resistencia a la flexión 406 / 300 MPa ISO 178
Resistencia al impacto Charpy, +23°C 85 / 110 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 18 / 25 kJ/m² ISO 179/1eA
Propiedades térmicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 222 / * °C ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa 220 / * °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 220 / * °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 13 / * E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 50 / * E-6/K ISO 11359-1/-2
Combustibilidad a 1.5mm esp. nom. HB / * class IEC 60695-11-10
Espesores de probeta 1.5 / * mm -
Propiedades eléctricasSeco / CondUnidadesMétodo de ensayo
ISO Data
Indice comparativo de linea de fuga 500 / - - IEC 60112
Other Standards[S]
Resistividad volumétrica específica 1E13 / 1E11 Ohm*m IEC 60093
Resistividad superficial específica * / 1E10 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
Otras propiedadesSeco / CondUnidadesMétodo de ensayo
Absorción de agua 4.5 / * % Sim. to ISO 62
Absorción de humedad 1.2 / * % Sim. to ISO 62
Densidad 1690 / - kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado <80 °C -
Tiempo de pre-secado 4 - 6 h -
Temperatura de la masa 235 - 270 °C -
Temperatura del molde 40 - 80 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Estable contra el calor
Applicaciones
Automotriz, Electrica
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.