Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Rilsamid® AMN BLACK T6LD - PA12 - ARKEMA

Material Data Center offers the following functions for Rilsamid® AMN BLACK T6LD:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Rilsamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Texto del producto
PA12, MHLR, 12-010
Rilsamid® AMN BLACK T6LD resin is a black colored polyamide 12. This grade is designed for injection molding.


Caracteristicas de procesamiento y fisicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 57 / * cm³/10min ISO 1133
Temperatura 235 / * °C -
Carga 2.16 / * kg -
Contracción posterior al moldeo, paralelo 1.9 / * % ISO 294-4, 2577
Contracción posterior al moldeo, normal 1.8 / * % ISO 294-4, 2577
Propiedades mecánicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Módulo de tracción - / 1440 MPa ISO 527
Esfuerzo de fluencia - / 46 MPa ISO 527
Alarg. en límite elástico - / 6 % ISO 527
Alarg. nominal a rotura - / >50 % ISO 527
Resistencia al impacto Charpy c/entalla, +23°C - / 4 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C - / 5 kJ/m² ISO 179/1eA
Dureza Shore D 69 / * - ISO 7619-1
Propiedades térmicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 178 / * °C ISO 11357-1/-3
Otras propiedadesSeco / CondUnidadesMétodo de ensayo
Densidad 1020 / - kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola, Negro
Aditivos
Desmoldeante
Características especiales
Estable a la luz, Estable contra rayos U.V./interperie, Estable contra el calor
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Demás información
Moldeo por inyección

Processing conditions, Injection:

- Typical melt temperature (Min / Recommended / Max) : 230°C / 250°C / 270°C.
- Mold temperature : 20 - 40°C
- Drying time and temperature (only necessary for bags opened for more than two hours) : 4-6 hours at 80 - 90°C.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.