Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Styroflex® 2G66 - SB - INEOS Styrolution

Material Data Center offers the following functions for Styroflex® 2G66:
unit conversion, PDF datasheet print, comparison with other plastics, application examples, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Styroflex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Styroflex® 2G66 is a styrene-butadiene block copolymer (SBC) with the properties of a thermoplastic elastomer (S-TPE). Styroflex® 2G66 is the only S-TPE with a styrene content of at least 60 % styrene and a rubber fraction of at least 70 %. Characteristic properties of Styroflex® 2G66 are therefore: high transparency, excellent thermostability, very high elongation at break and high resilence. Styroflex® 2G66 is more polar than comparable SBS or SEBS grades and offers a good printability.
Applications: Styroflex® 2G66 is a very versatile material, suitable for a variety of applications: In multilayer (coextruded with PE-EVA), thin-gauge film for the supporting layer, Styroflex® 2G66 is used e.g. for packaging fresh meat. Styroflex® 2G66 is also used for the modification of styrenic polymers; e.g. blended with high impact polystyrene it improves the toughness and the stress cracking resistance (ESCR) significantly. Styroflex® 2G66 is also suited for two-component injection molding, especially with polystyrene, to which it has excellent adhesion. Styroflex® 2G66 and compounds based on Styroflex® may be used for conventional injection molding (eg. of toys) and the extrusion of profiles, flexible tubing and soft foams.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 14 cm³/10min ISO 1133
Temperatura 200 °C -
Carga 5 kg -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 120 MPa ISO 527
Esfuerzo de fluencia 4 MPa ISO 527
Alarg. en límite elástico 5 % ISO 527
Alarg. nominal a rotura >50 % ISO 527
Resistencia al impacto Charpy, +23°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C N kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Combustibilidad a 1.5mm esp. nom. HB class IEC 60695-11-10
Espesores de probeta 1.6 mm -
Combustibilidad a espesor h HB class IEC 60695-11-10
Espesores de probeta 3.2 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 100Hz 2.5 - IEC 62631-2-1
Constante dieléctrica, 1MHz 2.5 - IEC 62631-2-1
Resistividad volumétrica específica >1E13 Ohm*m IEC 62631-3-1
Resistividad superficial específica 1E15 Ohm IEC 62631-3-2
Propiedades opticasValorUnidadesMétodo de ensayo
ISO Data
Niebla 1.4 - ISO 14782
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.07 % Sim. to ISO 62
Absorción de humedad 0.07 % Sim. to ISO 62
Densidad 1000 kg/m³ ISO 1183
Propiedades mecánicas (Film)ValorUnidadesMétodo de ensayo
ISO Data
Resistencia al desgarro Elmendorf, paralelo 650 N ISO 6383-2
Resistencia al desgarro Elmendorf, normal 800 N ISO 6383-2
WVTR, 23°C/85%r.h. 0.27 g/(m²*d) ISO 15106-1/-2
Prop. de transm. de oxígeno, 23°C/0%r.h. 27.2 cm³/(m²*d*bar) ISO 15105-1/-2
Espesor de la muestra 0.05 mm -
Características
Procesamiento y forma de entrega
Moldeo por inyección, Extrusion del film, Extrusión de perfiles, Transfer Molding
Características especiales
Esterilizable
Certifications
Contacto con alimentos, Aprobación a contacto con alimentos 10/2011, Aprobado por el FDA 21 CFR, Grado médico, Biocompatibility ISO 10993, USP Class VI, Drug Master File, Long term supply assurance
Applicaciones
Médico
Disponibilidad regional
Demás información
Moldeo por inyección
PROCESSING
injection molding, Melt temperature, range: 190 - 220 °C
injection molding, Mold temperature, range: 30 - 50 °C
Extrusión de láminas
PROCESSING
Extrusion, Blown film, Melt temperature: 170 - 190 °C
Extrusion, Flat film, Melt temperature: 170 - 240 °C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.