Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of UNIBRITE™ UA-1200 - ASA - Nippon A&L Inc.

Material Data Center offers the following functions for UNIBRITE™ UA-1200:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Unibrite datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 40 cm³/10min ISO 1133
Temperatura 220 °C -
Carga 10 kg -
Other Standards[S]
Contracción posterior al moldeo, paralelo 0.5 % Producer Method
S: These properties are reported by the producer according standards that are different to our defaults.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de fluencia 49 MPa ISO 527
Módulo de flexión, 23°C 2350 MPa ISO 178
Resistencia a la flexión 75 MPa ISO 178
Resistencia al impacto Charpy c/entalla, +23°C 8 kJ/m² ISO 179/1eA
Dureza Rockwell R 113 - ISO 2039-2
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 82 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 77 E-6/K ISO 11359-1/-2
Combustibilidad a espesor h HB class IEC 60695-11-10
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1050 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 80 - 90 °C -
Tiempo de pre-secado 3 - 6 h -
Temperatura de la masa 200 - 260 °C -
Temperatura del molde 40 - 80 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Disponibilidad regional
Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.