Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VECTRA® A115 - LCP-GF15 - Celanese

Check here, which other Vectra datasheets, application examples or technical articles are available in Material Data Center

Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Funciones

Any use of this information falls under the rules of our disclaimer.

Texto del producto

Provides easier flow than A130. Slightly tougher, but may warp slightly more than A130 in some parts. 15% glass reinforced. Chemical abbreviation according to ISO 1043-1 : LCP Inherently flame retardant FDA compliant UL-Listing V-0 in natural and black at 0.44mm thickness per UL 94 flame testing. Relative-Temperature-Index (RTI) according to UL 746B: electricals 240°C, mechanicals 220°C at 0.85mm. UL = Underwriters Laboratories (USA)

Flammability at thickness h

V-0

-

Caracteristicas de procesamiento y fisicas	Valor	Unidades	Método de ensayo
ISO Data
Contracción posterior al moldeo, paralelo	0.1	%	ISO 294-4, 2577
Contracción posterior al moldeo, normal	0.4	%	ISO 294-4, 2577

Propiedades mecánicas	Valor	Unidades	Método de ensayo
ISO Data
Módulo de tracción	12000	MPa	ISO 527
Resistencia a la tracción	200	MPa	ISO 527
Alargamiento a rotura	3.1	%	ISO 527
Resistencia al impacto Charpy c/entalla, +23°C	70	kJ/m²	ISO 179/1eA

Propiedades térmicas	Valor	Unidades	Método de ensayo
ISO Data
Temperatura de fusión, 10°C/min	280	°C	ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa	230	°C	ISO 75-1/-2
Estabilidad al calor, 0.45 MPa	250	°C	ISO 75-1/-2
Temp. reblandecimiento Vicat, B	162	°C	ISO 306
Coef.de expansión térmica lineal, paralelo	10	E-6/K	ISO 11359-1/-2
Coef.de expansión térmica lineal, normal	18	E-6/K	ISO 11359-1/-2
Combustibilidad a espesor h	V-0	class	IEC 60695-11-10

Propiedades eléctricas	Valor	Unidades	Método de ensayo
ISO Data
Constante dieléctrica, 100Hz	3.5	-	IEC 62631-2-1
Constante dieléctrica, 1MHz	3	-	IEC 62631-2-1
Factor de pérdidas dieléctricas, 100Hz	200	E-4	IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz	180	E-4	IEC 62631-2-1
Resistividad volumétrica específica	1E13	Ohm*m	IEC 62631-3-1
Resistividad superficial específica	>1E15	Ohm	IEC 62631-3-2
Resistencia dieléctrica	34	kV/mm	IEC 60243-1

Otras propiedades	Valor	Unidades	Método de ensayo
Absorción de agua	0.006	%	Sim. to ISO 62
Absorción de humedad	0.003	%	Sim. to ISO 62
Densidad	1500	kg/m³	ISO 1183

Funciones

Características

Procesamiento y forma de entrega

Moldeo por inyección

Forma de suministro

Sémola, Negro, Color natural

Características especiales

Resistencia mejorada al fuego, Estable a la luz, Estable contra rayos U.V./interperie, Estable contra el calor

Certifications

Contacto con alimentos, Aprobado por el FDA 21 CFR

Disponibilidad regional

Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa

Demás información

Moldeo por inyección

Vectra resins are well known for their excellent thermal and hydrolytic stability. In order to ensure these properties are optimum, the resin should be dried correctly prior to processing. Vectra A-grades should be dried at 150 C for a minimum of 4 hours in a desiccant dryer.
A three-zone screw evenly divided into feed, compression, and metering zones is preferred. A higher percentage of feed flights may be needed for smaller machines: 1/2 feed, 1/4 compression, 1/4 metering.

Vectra LCPs are shear thinning, their melt viscosity decreases quickly as shear rate increases. For parts that are difficult to fill, the molder can increase the injection velocity to improve melt flow.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.