View Datasheet in other language

E-mail to a friend

Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Venelene® 2707AP - (PE-HD) - Poliolefinas Internacionales, C.A.

Material Data Center offers the following functions for Venelene® 2707AP:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Venelene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:

Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección

Any use of this information falls under the rules of our disclaimer.

Caracteristicas de procesamiento y fisicas

Valor

Unidades

Método de ensayo

ASTM Data

Índice de fluidez, MFI

5.5

g/10min

ASTM D 1238

Temperatura

190

°C

Carga

2.16

Propiedades mecánicas

Valor

Unidades

Método de ensayo

ASTM Data

Esfuerzo de fluencia a tracción

MPa

ASTM D 638

Esfuerzo de fractura a tracción

MPa

ASTM D 638

Alargamiento a la fluencia

ASTM D 638

Alargamiento a la rotura

1200

ASTM D 638

Módulo de flexión

670

MPa

ASTM D 790

Propiedades térmicas

Valor

Unidades

Método de ensayo

ASTM Data

Temperatura Vicat

125

°C

ASTM D 1525

Otras propiedades	Valor	Unidades	Método de ensayo
Densidad	949	kg/m³	ASTM D 792

Recomendación para procesamiento Moldeo por inyección	Valor	Unidades	Método de ensayo
Temperatura de la masa	190 - 220	°C	-
Temperatura del molde	<20	°C	-

Características

Procesamiento y forma de entrega

Moldeo por inyección

Características especiales

Alto impacto o modificado al impacto

Resistencia quimica

Resistencia química general, Resistencia al esfuerzo producido por condiciones ambientales, Resistencia a la oxidación

Certifications

Contacto con alimentos, Aprobado por el FDA 21 CFR

Disponibilidad regional

América del Sur y Centroaméric

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.