Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Vitane LFC 9350 - TPU - geba Kunststoffcompounds GmbH

Material Data Center offers the following functions for Vitane LFC 9350:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Vitane datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Propiedades eléctricas - Otras propiedades - Condiciones de transformación - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de tracción 15.5 MPa ISO 37
Alargamiento a rotura 130 % ISO 37
Dureza Shore D 50 - ISO 7619-1
Other Standards[S]
Tensión a 10% alargamiento 0.7 MPa DIN 53504
S: These properties are reported by the producer according standards that are different to our defaults.
Propiedades eléctricasValorUnidadesMétodo de ensayo
Other Standards[S]
Resistividad volumétrica específica 2 Ohm*m IEC 60093
Resistividad superficial específica 400 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1270 kg/m³ ISO 1183
Condiciones de transformaciónValorUnidadesMétodo de ensayo
ISO Data
Moldeo por inyección, temperatura de la masa 220 °C ISO 294
Moldeo por inyección, temperatura del molde 60 °C ISO 294
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado <80 °C -
Tiempo de pre-secado 4 - 6 h -
Humedad de procesamiento ≤0.02 % -
Temperatura de la masa 210 - 230 °C -
Temperatura del molde 40 - 80 °C -
Temperatura - zona de alimentación 60 - 80 °C -
Zona 1 210 - 220 °C -
Zona 2 210 - 220 °C -
Zona 3 220 - 230 °C -
Temperatura de boquilla 220 - 230 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Conductividad eléctrica aumentada
Resistencia quimica
Resistencia al aceite
Applicaciones
Electrica, Empacado
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.