Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of BERGADUR® PB40G10 - PBT-GF10 - Avient Corporation

Material Data Center offers the following functions for BERGADUR® PB40G10:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bergadur datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Condiciones de transformación
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Resistant. Negligible, reversible or no changes in mass and dimensions.

Please consider the information about the application of the materials.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 4500 MPa ISO 527
Resistencia a la tracción 90 MPa ISO 527
Alargamiento a rotura 3.8 % ISO 527
Módulo de plastodeformación, 1h 4400 MPa ISO 899-1
Módulo de plastodeformación, 1000h 2800 MPa ISO 899-1
Resistencia al impacto Charpy, +23°C 50 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C 45 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 7 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C 6 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 224 °C ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa 205 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 215 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 55 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 120 E-6/K ISO 11359-1/-2
Combustibilidad a 1.5mm esp. nom. HB class IEC 60695-11-10
Espesores de probeta 1.6 mm -
Combustibilidad a espesor h HB class IEC 60695-11-10
Espesores de probeta 0.8 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 1MHz 3.6 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 190 E-4 IEC 62631-2-1
Resistividad volumétrica específica >1E13 Ohm*m IEC 62631-3-1
Resistividad superficial específica >1E15 Ohm IEC 62631-3-2
Resistencia dieléctrica 28 kV/mm IEC 60243-1
Indice comparativo de linea de fuga 500 - IEC 60112
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.45 % Sim. to ISO 62
Absorción de humedad 0.18 % Sim. to ISO 62
Densidad 1370 kg/m³ ISO 1183
Condiciones de transformaciónValorUnidadesMétodo de ensayo
ISO Data
Moldeo por inyección, temperatura de la masa 240 °C ISO 294
Moldeo por inyección, temperatura del molde 80 °C ISO 294
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola
Disponibilidad regional
Europa
Demás información
Moldeo por inyección
Resistant. Negligible, reversible or no changes in mass and dimensions.

Please consider the information about the application of the materials.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.