Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Monprene® CP-18260 - TPE - Teknor Apex Co.

Material Data Center offers the following functions for Monprene® CP-18260:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Monprene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Deformación permanente por compresión a 23°C, 24h 27 % ISO 815
Deformación permanente por compresión a 70°C, 24h 48 % ISO 815
ASTM Data
Módulo en 100% alargamiento 1.8 MPa ASTM D 412
Módulo en 300% alargamiento 0.8 MPa ASTM D 412
Dureza A Shore 60 - ASTM D 2240
Esfuerzo de fractura a tracción 7 MPa ASTM D 412
Alargamiento a la rotura 800 % ASTM D 412
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 890 kg/m³ ASTM D 792
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 65 °C -
Tiempo de pre-secado 2 - 4 h -
Temperatura de la masa 180 - 230 °C -
Temperatura del molde 15 - 50 °C -
Zona 1 120 - 160 °C -
Zona 2 160 - 230 °C -
Zona 3 180 - 230 °C -
Temperatura de boquilla 180 - 230 °C -
Velocidad de giro de husillo 50 - 100 rpm -
Contrapresión 0.5 - 1.5 MPa -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola
Características especiales
Estable contra rayos U.V./interperie, Translucent
Características
Buenas propiedades de adhesión, Textura suave
Resistencia quimica
Resistencia química general
Applicaciones
Uso general
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.