Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Pebax® 5513 SP 01 - TPA - ARKEMA

Material Data Center offers the following functions for Pebax® 5513 SP 01:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Pebax datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Propiedades térmicas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Texto del producto
Polyether block amide Pebax® 5513 SP 01 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide.
Added to PA6, Pebax® 5513 SP 01 resin enhances the properties of PA6, especially at low temperatures and low humidity content, at the same time maintaining the transparency of the nylon film and improving its soft touch.
This SP grade has been developed to be heat and UV resistant.


Main applications:
  • PA6 film additive


Packaging:
This grade is delivered dried in sealed packaging (20 kg and 25 kg bags and 454 kg rigid containers) ready to be processed.

Shelf Life:
Two years from the delivery. For any use above this limit, please refer to our technical services.
Propiedades mecánicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Módulo de tracción - / 180 MPa ISO 527
Esfuerzo de fluencia 14 / 13 MPa ISO 527
Alarg. en límite elástico 32 / 30 % ISO 527
Alarg. nominal a rotura >50 / >50 % ISO 527
Resistencia al impacto Charpy c/entalla, -30°C - / 34 kJ/m² ISO 179/1eA
Resistencia a la tracción TPE 60 / * MPa ISO 527
Alargamiento a rotura TPE >300 / * % ISO 527
Dureza Shore D 54 / * - ISO 7619-1
Propiedades térmicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 195 / * °C ISO 11357-1/-3
Temp. reblandecimiento Vicat, B 169 / * °C ISO 306
Otras propiedadesSeco / CondUnidadesMétodo de ensayo
Absorción de agua 6.7 / * % Sim. to ISO 62
Absorción de humedad 1.3 / * % Sim. to ISO 62
Densidad 1090 / 1090 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección, Otros tipos de extrusión
Forma de suministro
Sémola
Características especiales
Galvanizable, Estable a la luz, Estable contra rayos U.V./interperie, Estable contra el calor
Características
Resina de mezcla
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico, América del Sur y Centroaméric, Próximo Oriente/Africa
Demás información
Moldeo por inyección

Processing conditions:

- Typical melt temperature (Min / Recommended / Max): 220°C / 240°C / 260°C.
- Typical mold temperature: 25–60°C.
- Drying time and temperature (only necessary for bags/containers opened for more than two hours): 5-7 hours at 70-90°C.
Otros tipos de extrusión

Processing conditions:

- Typical melt temperature (Min / Recommended / Max): 220°C / 235°C / 250°C.
- Drying time and temperature (only necessary for bags/containers opened for more than two hours): 5-7 hours at 70-90°C.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.