Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of POLYabs V0X - ABS - Polykemi AB

Material Data Center offers the following functions for POLYabs V0X:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Polyabs datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Índice de fluidez, MFI 18 g/10min ISO 1133
Temperatura 230 °C -
Carga 5 kg -
Contracción posterior al moldeo, paralelo 0.6 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.6 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de tracción 40 MPa ISO 527
Alarg. en límite elástico 6 % ISO 527
Módulo de flexión, 23°C 2000 MPa ISO 178
Resistencia al impacto Charpy c/entalla, +23°C 16 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 74 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 84 °C ISO 75-1/-2
Temp. reblandecimiento Vicat, A 98 °C ISO 306
Temp. reblandecimiento Vicat, B 85 °C ISO 306
Combustibilidad a 1.5mm esp. nom. V-0 class IEC 60695-11-10
Espesores de probeta 1.6 mm -
Combustibilidad a espesor h V-0 class IEC 60695-11-10
Espesores de probeta 3.2 mm -
Yellow Card disponible - -
Glow Wire Ignition Temperature (GWIT) 960 °C IEC 60695-2-13
GWIT - thickness tested (1) 2.5 mm -
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1160 kg/m³ ISO 1183
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Granulado
Características especiales
Resistencia mejorada al fuego
Disponibilidad regional
Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.