Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® B30 P2 G40 - PA6-GF40 - Nurel S.A.

Material Data Center offers the following functions for Promyde® B30 P2 G40:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Propiedades específicas del material
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 26 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carga 5 / * kg -
Contracción posterior al moldeo, paralelo 0.3 / * % ISO 294-4, 2577
Contracción posterior al moldeo, normal 0.4 / * % ISO 294-4, 2577
Propiedades mecánicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 13000 / 8500 MPa ISO 527
Esfuerzo de tracción 205 / 138 MPa ISO 527
Alargamiento a rotura 3 / 3.5 % ISO 527
Módulo de flexión, 23°C 10600 / 6500 MPa ISO 178
Resistencia al impacto Charpy, +23°C 95 / 100 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 16 / 22 kJ/m² ISO 179/1eA
Propiedades térmicasSeco / CondUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 222 / * °C ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa 213 / * °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 215 / * °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 16 / * E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 60 / * E-6/K ISO 11359-1/-2
ASTM Data
Combustibilidad UL 94 HB - UL 94
Espesores de probeta 1.5 mm -
Propiedades eléctricasSeco / CondUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 1MHz 3.9 / 6.5 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 190 / 1800 E-4 IEC 62631-2-1
Resistividad volumétrica específica 1E13 / 1E10 Ohm*m IEC 62631-3-1
Resistividad superficial específica * / 1E10 Ohm IEC 62631-3-2
Indice comparativo de linea de fuga 500 / 500 - IEC 60112
Otras propiedadesSeco / CondUnidadesMétodo de ensayo
Absorción de agua 6 / * % Sim. to ISO 62
Absorción de humedad 1.8 / * % Sim. to ISO 62
Densidad 1460 / - kg/m³ ISO 1183
Propiedades específicas del materialSeco / CondUnidadesMétodo de ensayo
ISO Data
Indice de viscosidad 145 / * cm³/g ISO 307, 1157, 1628
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características especiales
Estable contra el calor
Características
Estabilidad térmica
Applicaciones
Electrica
Disponibilidad regional
Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.