Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Supraplast® UPA 63 - UP-GF - Raschig GmbH

Material Data Center offers the following functions for Supraplast® UPA 63:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Supraplast datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades
Any use of this information falls under the rules of our disclaimer.
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Contracción posterior al moldeo, paralelo 0.2 % ISO 294-4, 2577
Conductibilidad termica de fusión 1 W/(m K) -
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 9000 MPa ISO 527
Esfuerzo de tracción 60 MPa ISO 527
Módulo de flexión, 23°C 17500 MPa ISO 178
Resistencia al impacto Charpy, +23°C 11 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 6 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 8.00 MPa 200 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 15 E-6/K ISO 11359-1/-2
Combustibilidad a espesor h V-0 class IEC 60695-11-10
Espesores de probeta 0.8 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 100Hz 5.5 - IEC 62631-2-1
Constante dieléctrica, 1MHz 4.5 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 100Hz 200 E-4 IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 200 E-4 IEC 62631-2-1
Resistividad volumétrica específica 1E13 Ohm*m IEC 62631-3-1
Resistividad superficial específica 1E14 Ohm IEC 62631-3-2
Resistencia dieléctrica 30 kV/mm IEC 60243-1
Indice comparativo de linea de fuga 600 - IEC 60112
ASTM Data
Resistencia al arco 4 s ASTM D 495
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.5 % Sim. to ISO 62
Densidad 2000 kg/m³ ISO 1183
Bulk density 750 kg/m³ -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Forma de suministro
Sémola
Disponibilidad regional
Norteamérica, Europa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.