Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultradur® B 6550 FC - PBT - BASF

Material Data Center offers the following functions for Ultradur® B 6550 FC:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, parameters for material models, CAE Interfaces

Check here, which other Ultradur datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Texto del producto
High viscosity extrusion grade of fibre optical cable sheaths for semi-finished products, profile and hollow rods in food conctact and sensitive applications.

The BASF Ultradur® FC (Food Contact) grades enable the industry to develop products for food contact applications which are in compliance with different food regulatory legislations, including regulation (EU) 10/2011, regulation (EC) 2023/2006 (GMP for materials in food contact) or FDA regulation 21 CFR. Additional food contact compliances may also be available. Please contact your local representative or plastics safety (E-Mail: plastics.safety@basf.com).

Abbreviated designation according to ISO 1043-1: PBT
Caracteristicas de procesamiento y fisicasValorUnidadesMétodo de ensayo
ISO Data
Indice de fluidez volumétrico, MVR 9 cm³/10min ISO 1133
Temperatura 250 °C -
Carga 2.16 kg -
Contracción posterior al moldeo, paralelo 1.7 % ISO 294-4, 2577
Contracción posterior al moldeo, normal 2.1 % ISO 294-4, 2577
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Módulo de tracción 2400 MPa ISO 527
Esfuerzo de fluencia 54 MPa ISO 527
Alarg. en límite elástico 3.5 % ISO 527
Alarg. nominal a rotura >50 % ISO 527
Módulo de plastodeformación, 1h 1800 MPa ISO 899-1
Módulo de plastodeformación, 1000h 1100 MPa ISO 899-1
Resistencia al impacto Charpy, +23°C N kJ/m² ISO 179/1eU
Resistencia al impacto Charpy, -30°C 250 kJ/m² ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C 6 kJ/m² ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C 3.5 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Temperatura de fusión, 10°C/min 223 °C ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa 55 °C ISO 75-1/-2
Estabilidad al calor, 0.45 MPa 135 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 110 E-6/K ISO 11359-1/-2
Coef.de expansión térmica lineal, normal 110 E-6/K ISO 11359-1/-2
Combustibilidad a 1.5mm esp. nom. HB class IEC 60695-11-10
Espesores de probeta 1.5 mm -
Combustibilidad a espesor h HB class IEC 60695-11-10
Espesores de probeta 0.8 mm -
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 100Hz 3.3 - IEC 62631-2-1
Constante dieléctrica, 1MHz 3.3 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 100Hz 10 E-4 IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 200 E-4 IEC 62631-2-1
Resistividad volumétrica específica >1E13 Ohm*m IEC 62631-3-1
Resistividad superficial específica 1E13 Ohm IEC 62631-3-2
Indice comparativo de linea de fuga 600 - IEC 60112
Otras propiedadesValorUnidadesMétodo de ensayo
Absorción de agua 0.5 % Sim. to ISO 62
Absorción de humedad 0.25 % Sim. to ISO 62
Densidad 1300 kg/m³ ISO 1183
Propiedades específicas del materialValorUnidadesMétodo de ensayo
ISO Data
Indice de viscosidad 160 cm³/g ISO 307, 1157, 1628
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 100 °C -
Tiempo de pre-secado 4 h -
Temperatura de la masa 250 - 275 °C -
Temperatura del molde 40 - 80 °C -
Funciones
Viscosidad-velocidad de cizallamiento , Ultradur® B 6550 FC, PBT, BASF
Tensión de cizalla-velocidad de cizalla , Ultradur® B 6550 FC, PBT, BASF
Esfuerzo-alargamiento , Ultradur® B 6550 FC, PBT, BASF
Módulo secante-alargamiento , Ultradur® B 6550 FC, PBT, BASF
Esfuerzo-alargamiento (isocrono) 23°C, Ultradur® B 6550 FC, PBT, BASF
Módulo de plastodeformación-tiempo 23°C, Ultradur® B 6550 FC, PBT, BASF
Curva de creep 23°C, Ultradur® B 6550 FC, PBT, BASF
Módulo a tensión-temperatura , Ultradur® B 6550 FC, PBT, BASF
Características
Procesamiento y forma de entrega
Moldeo por inyección, Extrusion del film, Extrusión de perfiles, Extrusión de láminas, Otros tipos de extrusión
Forma de suministro
Sémola
Certifications
Contacto con alimentos, Aprobación a contacto con alimentos 10/2011, Aprobado por el FDA 21 CFR
Disponibilidad regional
Demás información
Moldeo por inyección
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 250 - 275 °C
injection molding, Melt temperature, recommended: 260 °C
injection molding, Mold temperature, range: 40 - 80 °C
injection molding, Mold temperature, recommended: 60 °C
injection molding, Dwell time, thermoplastics: 10 min
Otros tipos de extrusión
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
Extrusion, Prepreg, Melt temperature: 230 - 250 °C
Extrusion, Pipes, Melt temperature: 230 - 260 °C
Extrusion, cable sheathing, Melt temperature: 230 - 260 °C
Extrusión de perfiles
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
Extrusion, Profiles, Melt temperature: 230 - 260 °C
Extrusión de placas
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 100 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
Extrusion, Plates, Melt temperature: 230 - 250 °C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.