Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VECTRA® MT®4310 - LCP-GF30 - Celanese

Check here, which other Vectra datasheets, application examples or technical articles are available in Material Data Center

Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Funciones

Any use of this information falls under the rules of our disclaimer.

Texto del producto

Vectra^® MT4310 VF3001 (natural) is a 30% glass reinforced high flow, LCP grade for injection molding.

Vectra^® MT4310 VF3001 (natural) is a special grade developed for medical industry applications and complies with:

• Food Contact Substance Notification (FCN) No. 742 of the Food and Drug Administration (FDA) and is listed in the Drug Master File (DMF 8464) and the Device Master File (MAF 315)
• the corresponding EU and national registry regulatory requirements
• biocompatibility in tests corresponding to USP 23 Class VI/ISO 10993
• low residual monomers
• no animal products

Highest temperature capability
Easiest flow
Suitable where very thin walls are required
Used for broad range of SMT applications, with minimal dimensional change
Chemical abbreviation according to ISO 1043-1 : LCP
Inherently flame retardant

Flammability at thickness h

V-0

-

Caracteristicas de procesamiento y fisicas	Valor	Unidades	Método de ensayo
ISO Data
Contracción posterior al moldeo, paralelo	0.1	%	ISO 294-4, 2577
Contracción posterior al moldeo, normal	0.5	%	ISO 294-4, 2577

Propiedades mecánicas	Valor	Unidades	Método de ensayo
ISO Data
Módulo de tracción	16000	MPa	ISO 527
Resistencia a la tracción	160	MPa	ISO 527
Alargamiento a rotura	1.6	%	ISO 527
Resistencia al impacto Charpy c/entalla, +23°C	40	kJ/m²	ISO 179/1eA

Propiedades térmicas	Valor	Unidades	Método de ensayo
ISO Data
Temperatura de fusión, 10°C/min	335	°C	ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa	276	°C	ISO 75-1/-2
Estabilidad al calor, 8.00 MPa	216	°C	ISO 75-1/-2
Temp. reblandecimiento Vicat, B	195	°C	ISO 306
Coef.de expansión térmica lineal, paralelo	7	E-6/K	ISO 11359-1/-2
Coef.de expansión térmica lineal, normal	20	E-6/K	ISO 11359-1/-2
Combustibilidad a espesor h	V-0	class	IEC 60695-11-10
Combustibilidad según índice de oxigeno	45	%	ISO 4589-1/-2

Propiedades eléctricas	Valor	Unidades	Método de ensayo
ISO Data
Constante dieléctrica, 100Hz	4	-	IEC 62631-2-1
Constante dieléctrica, 1MHz	3.3	-	IEC 62631-2-1
Factor de pérdidas dieléctricas, 100Hz	100	E-4	IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz	250	E-4	IEC 62631-2-1
Resistividad volumétrica específica	1E13	Ohm*m	IEC 62631-3-1
Resistividad superficial específica	1E14	Ohm	IEC 62631-3-2
Resistencia dieléctrica	32	kV/mm	IEC 60243-1

Otras propiedades	Valor	Unidades	Método de ensayo
Densidad	1610	kg/m³	ISO 1183

Funciones

Características

Procesamiento y forma de entrega

Moldeo por inyección

Forma de suministro

Sémola, Color natural

Características especiales

Resistencia mejorada al fuego, Estable a la luz, Esterilizable, Esterilización por óxido de etileno (EtO), Esterilización por vapor, Gamma irradiation sterilization

Certifications

Contacto con alimentos, Aprobación a contacto con alimentos BfR, Aprobado por el FDA 21 CFR, Food contact notification (FCN), Grado médico, Biocompatibility ISO 10993, USP Class VI, Drug Master File, Device Master File

Applicaciones

Médico

Disponibilidad regional

Norteamérica, Europa

Demás información

Moldeo por inyección

Vectra resins are well known for their excellent thermal and hydrolytic stability. In order to ensure these properties are optimum, the resin should be dried correctly prior to processing. Vectra LCP MT4310 and MT4350 should be dried at 150°C for a minimum of 6 hours or at 170°C for a minimum of 4 hours in a desiccant dryer.
A three-zone screw evenly divided into feed, compression, and metering zones is preferred. A higher percentage of feed flights may be needed for smaller machines: 1/2 feed, 1/4 compression, 1/4 metering.

Vectra LCPs are shear thinning, their melt viscosity decreases quickly as shear rate increases. For parts that are difficult to fill, the molder can increase the injection velocity to improve melt flow.

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.