Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Xyron™ X531Z - PPE-X10 - Asahi Kasei

Material Data Center offers the following functions for Xyron™ X531Z:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Xyron datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Recomendación para procesamiento Moldeo por inyección
Any use of this information falls under the rules of our disclaimer.
Propiedades mecánicasValorUnidadesMétodo de ensayo
ISO Data
Esfuerzo de tracción 71 MPa ISO 527
Módulo de flexión, 23°C 3600 MPa ISO 178
Resistencia a la flexión 119 MPa ISO 178
Resistencia al impacto Charpy c/entalla, +23°C 5 kJ/m² ISO 179/1eA
Propiedades térmicasValorUnidadesMétodo de ensayo
ISO Data
Estabilidad al calor, 1.80 MPa 118 °C ISO 75-1/-2
Coef.de expansión térmica lineal, paralelo 60 E-6/K ISO 11359-1/-2
Combustibilidad a espesor h V-0 class IEC 60695-11-10
Espesores de probeta 1.6 mm -
Combustibilidad 5V a espesor h 5VA class IEC 60695-11-20
Espesores de probeta 2.5 mm -
ASTM Data
Estabilidad al calor @ 264 psi 120 °C ASTM D 648
Propiedades eléctricasValorUnidadesMétodo de ensayo
ISO Data
Constante dieléctrica, 100Hz 3.1 - IEC 62631-2-1
Constante dieléctrica, 1MHz 3 - IEC 62631-2-1
Factor de pérdidas dieléctricas, 100Hz 30 E-4 IEC 62631-2-1
Factor de pérdidas dieléctricas, 1MHz 50 E-4 IEC 62631-2-1
Resistividad volumétrica específica 1E14 Ohm*m IEC 62631-3-1
Resistividad superficial específica 1E16 Ohm IEC 62631-3-2
Otras propiedadesValorUnidadesMétodo de ensayo
Densidad 1150 kg/m³ ISO 1183
Recomendación para procesamiento Moldeo por inyecciónValorUnidadesMétodo de ensayo
Temperatura de pre-secado 90 - 100 °C -
Tiempo de pre-secado 2 - 4 h -
Temperatura de la masa 250 - 300 °C -
Temperatura del molde 70 - 90 °C -
Características
Procesamiento y forma de entrega
Moldeo por inyección
Características
Baja deformación
Disponibilidad regional
Norteamérica, Europa, Asia Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.