Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of BERGADUR® PB40G10 - PBT-GF10 - Avient Corporation

Material Data Center offers the following functions for BERGADUR® PB40G10:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bergadur datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Préparation et conditionnement des éprouvettes
Any use of this information falls under the rules of our disclaimer.
Informations produit
Resistant. Negligible, reversible or no changes in mass and dimensions.

Please consider the information about the application of the materials.
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 4500 MPa ISO 527
Contrainte à la rupture 90 MPa ISO 527
Déformation à la rupture 3.8 % ISO 527
Module de fluage en traction, 1h 4400 MPa ISO 899-1
Module de fluage en traction, 1000h 2800 MPa ISO 899-1
Résistance au choc Charpy, +23°C 50 kJ/m² ISO 179/1eU
Résistance au choc Charpy, -30°C 45 kJ/m² ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C 7 kJ/m² ISO 179/1eA
Résistance au choc Charpy (entaillé), -30°C 6 kJ/m² ISO 179/1eA
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fusion, 10°C/min 224 °C ISO 11357-1/-3
Température de fléchissement s/chrg, 1.80 MPa 205 °C ISO 75-1/-2
Température de fléchissement s/chrg, 0.45 MPa 215 °C ISO 75-1/-2
Coeffic. de dilatation therm. linéique, parallèle 55 E-6/K ISO 11359-1/-2
Coeffic. de dilatation therm. linéique, perpend. 120 E-6/K ISO 11359-1/-2
Inflammabilité ep. nom. 1.5 mm HB class IEC 60695-11-10
Epaisseur de l'éprouvette 1.6 mm -
Inflammabilité pr. épaisseur h HB class IEC 60695-11-10
Epaisseur de l'éprouvette 0.8 mm -
Propriétés électriquesValeurUnitéNorme du test
ISO Data
Permittivité relative, 1MHz 3.6 - IEC 62631-2-1
Facteur de pertes, 1MHz 190 E-4 IEC 62631-2-1
Résistivité transversale >1E13 Ohm*m IEC 62631-3-1
Résistivité superficielle >1E15 Ohm IEC 62631-3-2
Rigidité diélectrique 28 kV/mm IEC 60243-1
Indice de résistance au cheminement 500 - IEC 60112
Propriétés diversesValeurUnitéNorme du test
Absorption d'eau 0.45 % Sim. to ISO 62
Absorption d'humidité 0.18 % Sim. to ISO 62
Masse volumique 1370 kg/m³ ISO 1183
Préparation et conditionnement des éprouvettesValeurUnitéNorme du test
ISO Data
Injection, température de la matière fondue 240 °C ISO 294
Injection, température du moule 80 °C ISO 294
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Granulés
Disponibilité régionale
Europe
Autres informations
Moulage par injection
Resistant. Negligible, reversible or no changes in mass and dimensions.

Please consider the information about the application of the materials.
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.