Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Dynalloy™ OBC8000-T40 - TPE - Avient Corporation

Material Data Center offers the following functions for Dynalloy™ OBC8000-T40:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Dynalloy datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ASTM Data
Retrait au moulage , parallèle 0.0145 mm/mm ASTM D 955
Retrait au moulage, perpendiculaire 0.0145 mm/mm ASTM D 955
Propriétés mécaniquesValeurUnitéNorme du test
ASTM Data
Module à 100% allongement 1.05 MPa ASTM D 412
Module à 300% allongement 0.52 MPa ASTM D 412
Dureté A Shore 43 - ASTM D 2240
Compression rémanente, 22 hr @ 73 °F 24 % ASTM D 395
Résistance de traction à la rupture 3.1 MPa ASTM D 412
Allongement à la rupture 790 % ASTM D 412
Propriétés diversesValeurUnitéNorme du test
Densité 880 kg/m³ ASTM D 792
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Température de la matière fondue 193 - 227 °C -
Température du moule 26.7 - 37 °C -
Zone 1 166 - 188 °C -
Zone 2 177 - 199 °C -
Zone 3 199 - 221 °C -
Température de la buse 199 - 221 °C -
Vitesse de rotation de vis 50 - 100 rpm -
Vitesse d'injection 25.4 - 76.2 mm/s -
Contre-pression 0 - 0.552 MPa -
Pression de maintien 0.276 - 1.24 MPa -
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Granulés
Propriétés spéciales
Transparent
Caractéristiques
Bonne adhérence, Soft Feel
Certifications
Contact alimentaire, FDA 21 CFR approbation
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.