Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NYLENE 406F - PA6 - Polymeric Resources Corporation

Material Data Center offers the following functions for NYLENE 406F:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Nylene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés mécaniques - Propriétés thermiques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Propriétés mécaniquesValeurUnitéNorme du test
ASTM Data
Module de traction 75.2 MPa ASTM D 638
Module de flexion 2758 MPa ASTM D 790
Izod choc avec entaille, 1/8 in 42.7 J/m ASTM D 256
Propriétés thermiquesValeurUnitéNorme du test
ASTM Data
DTUL à 66 psi 182 °C ASTM D 648
DTUL à 264 psi 71.1 °C ASTM D 648
Température de fusion 216 °C ASTM D 3418
Propriétés diversesValeurUnitéNorme du test
Densité 1130 kg/m³ ASTM D 792
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 66 - 82 °C -
Pré-séchage - temps 2 - 4 h -
L'humidité de traitement ≤0.2 % -
Température de la matière fondue 238 - 271 °C -
Température du moule 49 - 93 °C -
Zone 1 221 - 249 °C -
Zone 2 227 - 260 °C -
Zone 3 238 - 271 °C -
Température de la buse 238 - 271 °C -
Pressions d'injection 4 - 12 MPa -
Contre-pression 0 - 50 MPa -
Pression de maintien 3 - 9 MPa -
Temps de sejour maximum 6 min -
Caractéristiques
Transformation
Moulage par injection
Certifications
Contact alimentaire, FDA 21 CFR approbation, NSF 51 approbation
Applications
General Purpose, Emballage
Disponibilité régionale
Amérique du nord
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.