Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NYLENE® 607 - PA6 - Polymeric Resources Corporation

Material Data Center offers the following functions for NYLENE® 607:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Nylene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés mécaniques - Propriétés thermiques - Propriétés diverses - Recommandations pour la transformation Extrusion
Any use of this information falls under the rules of our disclaimer.
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Contrainte d'écoulement 85 MPa ISO 527
Module de flexion, 23°C 2750 MPa ISO 178
Résistance au choc Charpy, +23°C 8 kJ/m² ISO 179/1eU
ASTM Data
Module de traction 84.8 MPa ASTM D 638
Module de flexion 2758 MPa ASTM D 790
Résistance à la flexion 107 MPa ASTM D 790
Izod choc avec entaille, 1/8 in 48 J/m ASTM D 256
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 65 °C ISO 75-1/-2
ASTM Data
DTUL à 66 psi 186 °C ASTM D 648
DTUL à 264 psi 65 °C ASTM D 648
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1140 kg/m³ ISO 1183
Densité 1140 kg/m³ ASTM D 792
Recommandations pour la transformation ExtrusionValeurUnitéNorme du test
Pré-séchage - température 82 °C -
Pré-séchage - temps 2 - 4 h -
Température de la matière fondue 288 - 302 °C -
Température - Zone d'alimentation 260 - 277 °C -
Zone 1 271 - 293 °C -
Zone 2 288 - 302 °C -
Température de la buse 288 - 302 °C -
Caractéristiques
Transformation
Extrusion a film soufflé, Extrusion de films, Extrusion de tubes, Extrusion de profilés, Extrusion de plaques
Caractéristiques
Bon tirage, Tenue de la matière à l’état fondu
Applications
Emballage
Disponibilité régionale
Amérique du nord
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.