Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Stat-Tech™ AT-CB2/000 CR - POM-Z - Avient Corporation

Material Data Center offers the following functions for Stat-Tech™ AT-CB2/000 CR:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Stat-Tech datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ASTM Data
Retrait au moulage , parallèle 0.0265 mm/mm ASTM D 955
Propriétés mécaniquesValeurUnitéNorme du test
ASTM Data
Module en traction 3105 MPa ASTM D 638
Résistance de traction à la rupture 60.3 MPa ASTM D 638
Allongement à la rupture 15 % ASTM D 638
Module de flexion 2415 MPa ASTM D 790
Résistance à la flexion 92.9 MPa ASTM D 790
Izod choc avec entaille, 1/4 in 91.5 J/m ASTM D 256
Propriétés thermiquesValeurUnitéNorme du test
ASTM Data
DTUL à 66 psi 153 °C ASTM D 648
DTUL à 264 psi 105 °C ASTM D 648
Propriétés électriquesValeurUnitéNorme du test
ASTM Data
Résistance de la surface 1E8 Ohm ASTM D 257
Résistance volumique 1E7 Ohm*cm ASTM D 257
Propriétés diversesValeurUnitéNorme du test
Densité 1390 kg/m³ ASTM D 792
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 80 - 85 °C -
Pré-séchage - temps 2 - 3 h -
Température de la matière fondue 190 - 200 °C -
Température du moule 75 - 85 °C -
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Granulés
Caractéristiques
Copolymère
Applications
Avions et aéronautique, Automobile, IT / Machine de bureau, Électrotechnique et électrique, Carter
Disponibilité régionale
Asia Pacific
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.