Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox. Information about Biopolymers, a project by FH Hannover and M-Base Engineering & Software GmbH sponsored by Fachagentur Nachwachsende Rohstoffe (FNR).

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Treva™ OP6026NAT-71 - CAP - Eastman Chemical Co.

Material Data Center offers the following functions for Treva™ OP6026NAT-71:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Treva datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés diverses - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Informations produit

Eastman TREVA™ Renew engineering bioplastic OP6026-71 Natural is a new cellulose-based engineering bioplastic that offers both high performance and reduced environmental impact. Renew polymers enable a brand to reduce

consumption of fossil feedstock-based plastics, achieve sustainability targets without compromise, and be a fast mover in a growing market for sustainable consumer products.

TREVA is chemically resistant, dimensionally stable, flows well, is BPA-free, and has low birefringence.




Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ASTM Data
Retrait au moulage , parallèle 0.007 mm/mm ASTM D 955
Propriétés mécaniquesValeurUnitéNorme du test
ASTM Data
Module de traction d’élasticité 49 MPa ASTM D 638
Résistance de traction à la rupture 48 MPa ASTM D 638
Allongement à la rupture 18 % ASTM D 638
Module de flexion 1940 MPa ASTM D 790
Dureté Rockwell R 100 - ASTM D 785
Izod choc avec entaille, 1/8 in 216 J/m ASTM D 256
Izod choc avec entaille, bas température 100 J/m ASTM D 256
Température -40 °C -
Propriétés thermiquesValeurUnitéNorme du test
ASTM Data
DTUL à 66 psi 114 °C ASTM D 648
DTUL à 264 psi 99 °C ASTM D 648
Vicat température 135 °C ASTM D 1525
Propriétés diversesValeurUnitéNorme du test
Biobased content 48 % -
Absorption d’eau, 24hr 2.3 % ASTM D 570
Densité 1220 kg/m³ ASTM D 792
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 75 °C -
Pré-séchage - temps 4 h -
Température de la matière fondue 260 °C -
Température du moule 85 °C -
Vitesse d'injection 30 mm/s -
Temps de sejour maximum 4 min -
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Couleurs naturelles
Caractéristiques
Bas biréfringence
Certifications
Contient des ressources renouvelables
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.