Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Vitane LFC 9585 - TPU - geba Kunststoffcompounds GmbH

Material Data Center offers the following functions for Vitane LFC 9585:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Vitane datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés mécaniques - Propriétés électriques - Propriétés diverses - Préparation et conditionnement des éprouvettes - Recommandations pour la transformation Moulage par injection
Any use of this information falls under the rules of our disclaimer.
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Résistance à la traction 25 MPa ISO 37
Déformation à la rupture 480 % ISO 37
Dureté Shore A 85 - ISO 7619-1
Other Standards[S]
Contrainte à 10% de déformation 0.35 MPa DIN 53504
Contrainte à 100% de déformation 9.5 MPa DIN 53504
S: These properties are reported by the producer according standards that are different to our defaults.
Propriétés électriquesValeurUnitéNorme du test
Other Standards[S]
Résistivité transversale 1E9 Ohm*m IEC 60093
Résistivité superficielle 1E12 Ohm IEC 60093
S: These properties are reported by the producer according standards that are different to our defaults.
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1100 kg/m³ ISO 1183
Préparation et conditionnement des éprouvettesValeurUnitéNorme du test
ISO Data
Injection, température de la matière fondue 220 °C ISO 294
Injection, température du moule 60 °C ISO 294
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température <80 °C -
Pré-séchage - temps 4 - 6 h -
L'humidité de traitement ≤0.02 % -
Température de la matière fondue 210 - 230 °C -
Température du moule 40 - 80 °C -
Température - Zone d'alimentation 60 - 80 °C -
Zone 1 210 - 220 °C -
Zone 2 210 - 220 °C -
Zone 3 220 - 230 °C -
Température de la buse 220 - 230 °C -
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Couleurs naturelles
Propriétés spéciales
Conductivité électrique accrue
Résistance Chimique
Résistance aux huiles
Certifications
Contact alimentaire
Applications
Électrotechnique et électrique, Emballage
Disponibilité régionale
Europe
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.