Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of K-Resin® KR03 - SB - INEOS Styrolution

Material Data Center offers the following functions for K-Resin® KR03:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, cooling time calculation, CAE Interfaces

Check here, which other K-Resin datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Informations produit
K-Resin® KR03 processes very well in injection molding, providing good cycle times and design flexibility. K-Resin® KR03 alone or in blends, can be extruded into sheet and thermoformed on conventional equipment at high output rates. The favorable economics of K-Resin® SBC, along with high productivity, have made possible tough clear disposable drinking cups, lids and other packaging applications. K-Resin® KR03 will process on most conventional equipment, allowing the molder to run a crystal clear bottle without expensive machine modifications, special molds, different screws, or dryers. K-Resin® KR03 can be blow molded in a broad range of sizes and shapes, from small pill bottles and medical drainage units, to very tall display bottles. It also can be injection blow molded into extremely high impact bottles with glass-like clarity.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Indice de fluidité à chaud en volume, MVR 7.5 cm³/10min ISO 1133
Température 200 °C -
Charge 5 kg -
Indice de fluidité, MFI 7.5 g/10min ISO 1133
Température 200 °C -
Charge 5 kg -
Densité du fondu 907 kg/m³ -
Conductivité thermique du fondu 0.184 W/(m K) -
Chaleur spécifique du fondu 2300 J/(kg K) -
Température d'éjection 60 °C -
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 1500 MPa ISO 527
Contrainte d'écoulement 25 MPa ISO 527
Déformation au seuil d'écoulement 2.2 % ISO 527
Déformation nominale à la rupture >50 % ISO 527
Module de flexion, 23°C 1790 MPa ISO 178
Résistance au choc Charpy, +23°C N kJ/m² ISO 179/1eU
Résistance au choc Charpy (entaillé), +23°C 2 kJ/m² ISO 179/1eA
Dureté Shore D 63 - ISO 7619-1
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 61 °C ISO 75-1/-2
Température de fléchissement s/chrg, 0.45 MPa 76 °C ISO 75-1/-2
Température de ramolliss. Vicat, B 60 °C ISO 306
ASTM Data
Vicat température 85 °C ASTM D 1525
Propriétés optiquesValeurUnitéNorme du test
ASTM Data
Brillant 162 - ASTM D 2457
Lumière á Transmittance 92 % ASTM D 1003
Propriétés diversesValeurUnitéNorme du test
Absorption d'humidité 0.07 % Sim. to ISO 62
Masse volumique 1010 kg/m³ ISO 1183
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 50 °C -
Pré-séchage - temps 3 - 4 h -
Température de la matière fondue 180 - 240 °C -
Température du moule 30 - 50 °C -
Caractéristiques
Transformation
Moulage par injection, Extrusion de plaques, Soufflage, Thermoformage
Conditionnement
Granulés
Propriétés spéciales
Transparent
Caractéristiques
Mélange de résine, High Gloss, Copolymère
Certifications
Grade médical, Device Master File
Applications
Médical, Emballage
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique
Autres informations
Moulages par injection
As a rule, the K-Resin® granules do not have to be pre-dried. However, in the event of unfavorable storage or transportation conditions involving severe temperature fluctuations, moisture can condense on the surface of the granules and this then has to be removed in a pre-drying step. The granules should be pre-dried in a dry-air dryer for 3 to 4 hours at a temperature of about 50°C.

PROCESSING

Melt temperature, range: 180 - 240°C

Mold temperature, range: 30 - 50°C

Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.