Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Makroblend® UT5207 - (PC+PBT)-I - Covestro Deutschland AG

Material Data Center offers the following functions for Makroblend® UT5207:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Makroblend datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Informations produit
  • (PC PBT)-blend, impact modified, easy release, UV-stabilized, injection molding grade. Makroblend UT5207 offers an exceptional low-temperature impact strength, good flowability and excellent chemical resistance. Suitable for metal insert molding.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ISO Data
Indice de fluidité à chaud en volume, MVR 21 cm³/10min ISO 1133
Température 260 °C -
Charge 5 kg -
Propriétés mécaniquesValeurUnitéNorme du test
ISO Data
Module en traction 2000 MPa ISO 527
Contrainte d'écoulement 55 MPa ISO 527
Déformation au seuil d'écoulement 4.5 % ISO 527
Déformation nominale à la rupture >50 % ISO 527
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fléchissement s/chrg, 1.80 MPa 75 °C ISO 75-1/-2
Température de fléchissement s/chrg, 0.45 MPa 100 °C ISO 75-1/-2
Propriétés électriquesValeurUnitéNorme du test
ISO Data
Permittivité relative, 100Hz 3.2 - IEC 62631-2-1
Permittivité relative, 1MHz 3.1 - IEC 62631-2-1
Facteur de pertes, 100Hz 30 E-4 IEC 62631-2-1
Facteur de pertes, 1MHz 150 E-4 IEC 62631-2-1
Résistivité transversale >1E13 Ohm*m IEC 62631-3-1
Résistivité superficielle >1E15 Ohm IEC 62631-3-2
Indice de résistance au cheminement 225 - IEC 60112
Propriétés diversesValeurUnitéNorme du test
Masse volumique 1220 kg/m³ ISO 1183
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 100 - 105 °C -
Pré-séchage - temps 2 - 4 h -
L'humidité de traitement ≤0.01 % -
Température de la matière fondue 250 - 270 °C -
Température du moule 60 - 80 °C -
Caractéristiques
Transformation
Moulage par injection
Conditionnement
Granulés
Additifs
Agent de démoulage
Propriétés spéciales
Modifié choc, Stabilisé aux intempéries
Résistance Chimique
Résistance chimique générale
Disponibilité régionale
Autres informations
Moulages par injection
PREPROCESSING
Max. Water content: 0.01 %
Drying temperature: 100 - 105 °C
Drying time:
Circulating air drying oven (50 % fresh air) 4-12 h
Fresh air dryer (high speed dryer) 2-4 h
Dry air dryer 2-4 h

PROCESSING
Melt temperature: 250-270 °C
Mold temperature: 60-80 °C

Use open nozzle.
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.