Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Promyde® BF33 L - PA6 - Nurel S.A.

Material Data Center offers the following functions for Promyde® BF33 L:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Promyde datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Propriétés thermiques - Propriétés optiques - Propriétés diverses - Propriétés mécaniques (Grades film) - Recommandations pour la transformation Extrusion
Any use of this information falls under the rules of our disclaimer.
Propriétés thermiquesValeurUnitéNorme du test
ISO Data
Température de fusion, 10°C/min 220 °C ISO 11357-1/-3
Propriétés optiquesValeurUnitéNorme du test
ASTM Data
Haze 5[1] % ASTM D 1003
1: Chill roll temperature 90ºC
Propriétés diversesValeurUnitéNorme du test
Absorption d'eau 9 % Sim. to ISO 62
Absorption d'humidité 3 % Sim. to ISO 62
Masse volumique 1130 kg/m³ ISO 1183
Moisture Content 0.1 % -
Propriétés mécaniques (Grades film)ValeurUnitéNorme du test
ISO Data
Contrainte au seuil, parallèle 34 MPa ISO 527-3
Contrainte à la rupture, parallèle 96 MPa ISO 527-3
Déformation maximale, parallèle 350 % ISO 527-3
Résistance au déchirement pantalon, parallèle 25 N/mm ISO 6383-1
Coefficient de friction dynamique 0.25 - ISO 8295
Perméabilité à la vapeur d'eau, 23°C/85%r.h. 15 g/(m²*d) ISO 15106-1/-2
Perméabilité à l'oxygène, 23°C/0%r.h. 25 cm³/(m²*d*bar) ISO 15105-1/-2
Perméabilité à l'oxygène, 23°C/85%r.h. 40 cm³/(m²*d*bar) ISO 15105-1/-2
Recommandations pour la transformation ExtrusionValeurUnitéNorme du test
Pré-séchage - température 75 - 80 °C -
Température - Zone d'alimentation 230 - 240 °C -
Zone 1 255 - 260 °C -
Température de la buse 255 - 265 °C -
Caractéristiques
Transformation
Extrusion de films, Extrusion (autres), Thermoformage
Additifs
Lubrifiant
Caractéristiques
Propriétés barrière
Résistance Chimique
Résistance chimique générale
Certifications
Contact alimentaire
Applications
Monofilament, Emballage
Disponibilité régionale
Europe
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.