Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of PermaStat® 600 - ABS - RTP Company

Material Data Center offers the following functions for PermaStat® 600:
unit conversion, PDF datasheet print, comparison with other plastics, application examples, CAE Interfaces

Check here, which other RTP datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caractéristiques des transformations/physiquesValeurUnitéNorme du test
ASTM Data
Retrait au moulage , parallèle 0.007 mm/mm ASTM D 955
Propriétés mécaniquesValeurUnitéNorme du test
ASTM Data
Module en traction 1931 MPa ASTM D 638
Module de traction 41.4 MPa ASTM D 638
Module de flexion 2137 MPa ASTM D 790
Résistance à la flexion 68.9 MPa ASTM D 790
Izod choc avec entaille, 1/8 in 214 J/m ASTM D 256
Propriétés thermiquesValeurUnitéNorme du test
ASTM Data
UL 94 inflammabilité HB - UL 94
Épaisseur testée 1.59 mm -
DTUL à 264 psi 76.7 °C ASTM D 648
Propriétés électriquesValeurUnitéNorme du test
ASTM Data
Résistance de la surface 9.9E11 Ohm ASTM D 257
Résistance volumique 9.9E10 Ohm*cm ASTM D 257
Propriétés diversesValeurUnitéNorme du test
Densité 1060 kg/m³ ASTM D 792
Moisture Content 0.1 % -
Recommandations pour la transformation Moulage par injectionValeurUnitéNorme du test
Pré-séchage - température 82.2 °C -
Pré-séchage - temps 2 h -
Température de la matière fondue 199 - 238 °C -
Température du moule 48.9 - 93.3 °C -
Pressions d'injection 68.9 - 103 MPa -
Caractéristiques
Transformation
Moulage par injection
Propriétés spéciales
Antistatique
Disponibilité régionale
Amérique du nord, Europe, Asia Pacific
Conditions générales
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.