Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VECTRA® A115 - LCP-GF15 - Celanese

Check here, which other Vectra datasheets, application examples or technical articles are available in Material Data Center

Caractéristiques des transformations/physiques - Propriétés mécaniques - Propriétés thermiques - Propriétés électriques - Propriétés diverses - Fonctions

Any use of this information falls under the rules of our disclaimer.

Informations produit

Provides easier flow than A130. Slightly tougher, but may warp slightly more than A130 in some parts. 15% glass reinforced. Chemical abbreviation according to ISO 1043-1 : LCP Inherently flame retardant FDA compliant UL-Listing V-0 in natural and black at 0.44mm thickness per UL 94 flame testing. Relative-Temperature-Index (RTI) according to UL 746B: electricals 240°C, mechanicals 220°C at 0.85mm. UL = Underwriters Laboratories (USA)

Flammability at thickness h

V-0

-

Caractéristiques des transformations/physiques	Valeur	Unité	Norme du test
ISO Data
Retrait au moulage, parallèle	0.1	%	ISO 294-4, 2577
Retrait au moulage, perpendiculaire	0.4	%	ISO 294-4, 2577

Propriétés mécaniques	Valeur	Unité	Norme du test
ISO Data
Module en traction	12000	MPa	ISO 527
Contrainte à la rupture	200	MPa	ISO 527
Déformation à la rupture	3.1	%	ISO 527
Résistance au choc Charpy (entaillé), +23°C	70	kJ/m²	ISO 179/1eA

Propriétés thermiques	Valeur	Unité	Norme du test
ISO Data
Température de fusion, 10°C/min	280	°C	ISO 11357-1/-3
Température de fléchissement s/chrg, 1.80 MPa	230	°C	ISO 75-1/-2
Température de fléchissement s/chrg, 0.45 MPa	250	°C	ISO 75-1/-2
Température de ramolliss. Vicat, B	162	°C	ISO 306
Coeffic. de dilatation therm. linéique, parallèle	10	E-6/K	ISO 11359-1/-2
Coeffic. de dilatation therm. linéique, perpend.	18	E-6/K	ISO 11359-1/-2
Inflammabilité pr. épaisseur h	V-0	class	IEC 60695-11-10

Propriétés électriques	Valeur	Unité	Norme du test
ISO Data
Permittivité relative, 100Hz	3.5	-	IEC 62631-2-1
Permittivité relative, 1MHz	3	-	IEC 62631-2-1
Facteur de pertes, 100Hz	200	E-4	IEC 62631-2-1
Facteur de pertes, 1MHz	180	E-4	IEC 62631-2-1
Résistivité transversale	1E13	Ohm*m	IEC 62631-3-1
Résistivité superficielle	>1E15	Ohm	IEC 62631-3-2
Rigidité diélectrique	34	kV/mm	IEC 60243-1

Propriétés diverses	Valeur	Unité	Norme du test
Absorption d'eau	0.006	%	Sim. to ISO 62
Absorption d'humidité	0.003	%	Sim. to ISO 62
Masse volumique	1500	kg/m³	ISO 1183

Fonctions

Caractéristiques

Transformation

Moulage par injection

Conditionnement

Granulés, Noir, Couleurs naturelles

Propriétés spéciales

Ignifugé, Stabilisé à la lumière, Stabilisé aux intempéries, Stabilisé à la chaleur

Certifications

Contact alimentaire, FDA 21 CFR approbation

Disponibilité régionale

Amérique du nord, Europe, Asia Pacific, South and Central America, Proche-Orient/Afrique

Autres informations

Moulages par injection

Vectra resins are well known for their excellent thermal and hydrolytic stability. In order to ensure these properties are optimum, the resin should be dried correctly prior to processing. Vectra A-grades should be dried at 150 C for a minimum of 4 hours in a desiccant dryer.
A three-zone screw evenly divided into feed, compression, and metering zones is preferred. A higher percentage of feed flights may be needed for smaller machines: 1/2 feed, 1/4 compression, 1/4 metering.

Vectra LCPs are shear thinning, their melt viscosity decreases quickly as shear rate increases. For parts that are difficult to fill, the molder can increase the injection velocity to improve melt flow.

Conditions générales

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.