Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of AKROLOY® PA ICF 30 black (5269) - (PA66+PA6I/6T)-CF30 - Akro-Plastic GmbH

Material Data Center offers the following functions for AKROLOY® PA ICF 30 black (5269):
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Akroloy datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche Fisichesecco/condUnitáNorma del test
ISO Data
Ritiro di stampaggio, parallelo 0.2 / * % ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare 0.4 / * % ISO 294-4, 2577
Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 25000 / 23000 MPa ISO 527
Carico unitario a rottura 220 / 200 MPa ISO 527
Deformazione a rottura 1.5 / 1.6 % ISO 527
Modulo a flessione, 23°C 21000 / 21000 MPa ISO 178
Resistenza alla flessione 320 / 300 MPa ISO 178
Resistenza all'urto Charpy, +23°C 50 / 50 kJ/m² ISO 179/1eU
Resistenza all'urto Charpy, -30°C 40 / 40 kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 7 / 7 kJ/m² ISO 179/1eA
Resist. urto Charpy con intaglio, -30°C 6 / 6 kJ/m² ISO 179/1eA
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 255 / * °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 230 / * °C ISO 75-1/-2
Reazione al fuoco a spessore h HB / * class IEC 60695-11-10
Spessore provato 0.8 / * mm -
Proprietà Elettrichesecco/condUnitáNorma del test
ISO Data
Resistività superficiale * / 10000 Ohm IEC 62631-3-2
Altre Proprietàsecco/condUnitáNorma del test
Massa volumica 1290 / - kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Temperatura di fusione 320 °C -
Temperatura dello stampo 100 °C -
Pressione di Iniezione 75 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Nero
Caratteristiche
Grado tribologico
Disponibilità geografica
Europa, Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.