Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of AVALON® 60 ABX - TPU - Huntsman Polymers Corp.

Material Data Center offers the following functions for AVALON® 60 ABX:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Avalon datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Proprietà MeccanicheValoreUnitáNorma del test
Other Standards[S]
Resistenza a trazione 15 MPa DIN 53504
Deformazione a rottura 600 % DIN 53504
Resistenza alla lacerazione 20 kN/m DIN 53515
Resistenza all'abrasione 90 mm³ DIN 53516
Durezza Shore A 60 - DIN 53505
S: These properties are reported by the producer according standards that are different to our defaults.
Altre ProprietàValoreUnitáNorma del test
Other Standards[S]
Massa volumica 1080 kg/m³ DIN 53479
S: These properties are reported by the producer according standards that are different to our defaults.
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 80 - 90 °C -
Pre-essiccamento - Tempo 2 h -
Temperatura dello stampo 25 - 50 °C -
Temperatura - Zona di Alimentazione 25 - 35 °C -
Zona 1 150 - 170 °C -
Zona 2 155 - 175 °C -
Zona 3 155 - 180 °C -
Temperatura dell ugello 150 - 175 °C -
Velocità di Rotazione della Vite 20 - 80 rpm -
Pressione di Iniezione 2 - 10 MPa -
Contropressione 0.03 - 0.3 MPa -
Pressione di chiusura 1 - 5 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche
Antisdrucciolo, Resistente ai graffi
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.