Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of CELANEX® PBT 357 FR - PBT - Celanese

Material Data Center offers the following functions for CELANEX® PBT 357 FR:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Celanex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 0.8 cm³/10min ISO 1133
Temperatura 250 °C -
Carico 2.16 kg -
Ritiro di stampaggio, parallelo 0.7 % ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare 0.6 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 1981 MPa ISO 527
Carico unitario a trazione 47 MPa ISO 527
Deformazione a snervamento 4.9 % ISO 527
Resistenza all'urto Charpy, +23°C N kJ/m² ISO 179/1eU
Resistenzia all'urto Charpy con intaglio, +23°C 17 kJ/m² ISO 179/1eA
Resistenzia all'urto Charpy con intaglio, -30°C 9 kJ/m² ISO 179/1eA
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 94 °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 105 °C ISO 75-1/-2
Temp.di rammollimento Vicat, B 113 °C ISO 306
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1280 kg/m³ ISO 1183
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Altre informazioni
Stampaggio ad Iniezione
To avoid hydrolytic degradation during processing, CELANEX resins have to be dried to a moisture level equal to or less than 0.02%. Drying should be done in a dehumidifying hopper dryer capable of dewpoints <-30°F (-34°C) at 250°F (121°C) for 4 hours.
Rear Temperature 480-520(249-271) deg F (deg C)
Center Temperature 480-530(249-276) deg F (deg C)
Front Temperature 480-530(249-276) deg F (deg C)
Nozzle Temperature 480-530(249-276) deg F (deg C)
Melt Temperature 480-520(249-271) deg F (deg C)
Mold Temperature 80-180(27-82) deg F (deg C)
Back Pressure 50-100 psi
Screw Speed Medium
Injection Speed Fast

Injection speed, injection pressure and holding pressure have to be optimized to the individual article geometry. To avoid material degradation during processing low back pressure and minimum screw speed have to be used. Overheating of the material has to be avoided, in particular for flame retardant grades.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.