Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of DURANEX® 330NF - PBT-GF30 - Polyplastics

Material Data Center offers the following functions for DURANEX® 330NF:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Duranex datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Resistenza a trazione 100 MPa ISO 527
Deformazione a rottura 1.7 % ISO 527
Modulo a flessione, 23°C 10100 MPa ISO 178
Resistenza alla flessione 147 MPa ISO 178
Resist. urto Charpy con intaglio, +23°C 7 kJ/m² ISO 179/1eA
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 214 °C ISO 75-1/-2
Reazione al fuoco a spessore h V-0 class IEC 60695-11-10
Spessore provato 0.4 mm -
Yellow Card disponibile sì - -
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
Proprietà ElettricheValoreUnitáNorma del test
ISO Data
Resistività volumica 3E14 Ohm*m IEC 62631-3-1
Resistività superficiale 4E16 Ohm IEC 62631-3-2
Rigidità dielettrica 22 kV/mm IEC 60243-1
Res. Alle correnti striscianti superficiali 600 - IEC 60112
ASTM Data
Resistenza all’arco 128 s ASTM D 495
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1570 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Temperatura dello stampo 60 °C -
Zona 1 230 °C -
Zona 2 260 °C -
Zona 3 260 °C -
Velocità di iniezione 67 mm/s -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Ritardante di fiamma, Senza alogeni, Stabilizzato o stabile alla luce, Estab. agli U.V. o per applicaz.in esterni, Stabilizzato o stabile al calore
Certifications
RoHS
Applicazioni
Elettrotecnica ed electrici
Disponibilità geografica
Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.