Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Iupital FL2020 - (POM+PTFE) - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for Iupital FL2020:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Iupital datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 4.7 cm³/10min ISO 1133
Temperatura 190 °C -
Carico 2.16 kg -
Indice di Fluiditá, MFI 6 g/10min ISO 1133
Temperatura 190 °C -
Carico 2.16 kg -
Ritiro di stampaggio, parallelo 2.1 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Modulo a trazione 2400 MPa ISO 527
Carico unitario a trazione 44 MPa ISO 527
Deformazione a snervamento 8 % ISO 527
Deformazione a rottura 15 % ISO 527
Modulo a flessione, 23°C 2200 MPa ISO 178
Resistenza alla flessione 67 MPa ISO 178
Resistenza all'urto Charpy, +23°C 50 kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 5 kJ/m² ISO 179/1eA
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 166 °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 96 °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 151 °C ISO 75-1/-2
Reazione al fuoco a spessore h HB class IEC 60695-11-10
Spessore provato 0.8 mm -
Yellow Card disponibile - -
Proprietà ElettricheValoreUnitáNorma del test
ISO Data
Resistività volumica 1E12 Ohm*m IEC 62631-3-1
Resistività superficiale 1E16 Ohm IEC 62631-3-2
Altre ProprietàValoreUnitáNorma del test
Assorbimento d'umidità 0.18 % Sim. alla ISO 62
Massa volumica 1510 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 80 °C -
Pre-essiccamento - Tempo 3 - 4 h -
Temperatura dello stampo 50 - 100 °C -
Zona 1 170 °C -
Zona 2 180 °C -
Zona 3 190 °C -
Temperatura dell ugello 180 - 210 °C -
Velocità di Rotazione della Vite 80 - 120 rpm -
Pressione di Iniezione 50 - 100 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Additivi
Lubrificanti
Caratteristiche
Copolimero
Applicazioni
Automotive, Elettrotecnica ed electrici, Polivalente
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.