Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUMID HI5006A - (PA6+ABS) - LG Chem

Material Data Center offers the following functions for LUMID HI5006A:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Lumid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ASTM Data
Indice di fluidità a caldo, MFI 7.5 g/10min ASTM D 1238
Temperatura 240 °C -
Carico 5 kg -
Ritiro di stampaggio, parallelo 0.01 mm/mm ASTM D 955
Proprietà MeccanicheValoreUnitáNorma del test
ASTM Data
Resistenza alla trazione di snervamento 44.1 MPa ASTM D 638
Allungamento a rottura 100 % ASTM D 638
Modulo a flessione 1570 MPa ASTM D 790
Resistenza alla flessione 58.9 MPa ASTM D 790
Resistenza all'urto Izod con intaglio, 1/4 in 687 J/m ASTM D 256
Proprietà TermicheValoreUnitáNorma del test
ASTM Data
coefficiente d’espansione termica, lung. 80 E-6/K ASTM D 696
DTUL a 66 psi 110 °C ASTM D 648
DTUL a 264 psi 80 °C ASTM D 648
Temperatura di fusione 220 °C ASTM D 3418
Proprietà ElettricheValoreUnitáNorma del test
ASTM Data
Rigidità elettrica, breve periodo di tempo 26 kV/mm ASTM D 149
Costante dielèttrica, 1 MHz 2.9 - ASTM D 150
Resistenza di volume 1E13 Ohm*cm ASTM D 257
Altre ProprietàValoreUnitáNorma del test
Densità 1060 kg/m³ ASTM D 792
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 70 - 90 °C -
Pre-essiccamento - Tempo 4 - 5 h -
Umidità del Processo ≤0.1 % -
Temperatura di fusione 250 - 265 °C -
Temperatura dello stampo 80 - 100 °C -
Zona 1 235 - 250 °C -
Zona 2 240 - 260 °C -
Zona 3 240 - 260 °C -
Temperatura dell ugello 250 - 265 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Alto urto o modificato all'urto
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.