Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NYLENE® 5105 - PA66-GF5 - Polymeric Resources Corporation

Material Data Center offers the following functions for NYLENE® 5105:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Nylene datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Caratteristiche Fisiche - Proprietà Meccaniche - Proprietà Termiche - Altre Proprietà - Raccomandazione de Processabilità Stampaggio ad Iniezione
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ASTM Data
Ritiro di stampaggio, parallelo 0.07 mm/mm ASTM D 955
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Resistenza a trazione 74 MPa ISO 527
Modulo a flessione, 23°C 2850 MPa ISO 178
Resistenza all'urto Charpy, +23°C 27 kJ/m² ISO 179/1eU
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 255 °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 221 °C ISO 75-1/-2
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1140 kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 65 - 82 °C -
Pre-essiccamento - Tempo 2 - 4 h -
Umidità del Processo ≤0.2 % -
Temperatura di fusione 287 - 316 °C -
Temperatura dello stampo 49 - 93 °C -
Zona 1 260 - 293 °C -
Zona 2 277 - 299 °C -
Zona 3 282 - 310 °C -
Temperatura dell ugello 279 - 307 °C -
Pressione di Iniezione 5 - 15 MPa -
Contropressione 0 - 50 MPa -
Pressione di chiusura 4 - 12 MPa -
Tempo di residenza, massimo 6 min -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Additivi
Lubrificanti
Resistenza Chimica
Resistenza chimica generale
Applicazioni
Automotive, Polivalente
Disponibilità geografica
Nord America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.